60 polycarbonate plate 3d models

It's printed withtransparent filament to do not highlight the fixing part when sun traverse the sheets of polycarbonate Print Settings Printer Brand: Anet Printer: A8 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.1 Infill: 20%...

Print Settings: Printer Brand: Ultimaker Printer: Ultimaker Original Rafts: No Supports: Yes Resolution: 0.100 mm Infill: 3mm Polycarbonate ultimaker Notes: Polycarbonate: 260° + capton t° p.: 110° 0.100mm 30mm/s No brim no Fan Ninjaflex semiflex:...

... numerous TV shows featuring the use of see-through dry erase boards. After extensive research, I discovered that polycarbonate works remarkably well as a dry erase surface, while also being transparent and incredibly impact resistant/bulletproof.

Important Warning: The heaters are 220-volt devices, so make sure to earth the enclosure using aluminium squares, as polycarbonate is not conductive. Using Wago or similar connectors should be safe. If you need any help with measurements or...

I needed a piece that will hold down a polycarbonate sheet, so I could safely use it in Airsoft. I also went ahead and added a killflash. (because why not!) It's designed to be glued to the front of the monocular. I used a glue commonly used in...

...p = LD020411878172015024 lipo: 2S 300mha: +/- 3-4min, 500mha 2S: +/- 5-6min vis: 8 x M1.6 x 5mm Attention polycarbonate transparent dans Ultimaker est très fragile par rapport au noir qui est très résistant !!!! ...https://www.facebook.com/Microdure/

Human: 90mm Frame Polycarbonate Ultimaker FC: http://www.banggood.com/Eachine-32bits-F3-Brushed-Flight-Control-Board-Based-On-SP-RACING-F3-EVO-For-Micro-FPV-Frame-p-1076530.html?p=LD020411878172015024 Coreless:...

... Lipo: 300mha 2S: +/- 3-4min, 500mha 2S: +/- 5-6min Screws: 8 x M1.6 x 5mm Attention! ...Polycarbonate in Ultimaker is extremely fragile compared to black, which is incredibly resistant! ...https://www.facebook.com/Microdure/

Made for my cheap aliexpress "nikula" monocular. I needed a piece that will hold down a polycarbonate sheet, so I could safely use it in Airsoft. I also went ahead and added a killflash. (because why not!)</p> <p>It's designed to be glued to the...

Here is one of my latest Ultimaker Polycarbonate prototype. ...Built with rest of material "drawer bottom" A 160mm Quadcopter equipped with 79mm CW & CCW turbines:...

Here is one of my latest Ultimaker Polycarbonate prototype. Built with rest of material drawer bottom. ... A 160mm Quadcopter equipped with 79mm CW & CCW turbines:...

Here is one of my latest Ultimaker Polycarbonate prototypes. I've been experimenting with the rest of the material, and I think I've come up with a great design for a "drawer bottom". A 160mm Quadcopter equipped with 79mm CW & CCW turbines has been...

A small meeting room with plexiglass books shelving. The panels of the walls and roof can be translucent to let exterior light pass or opaque. On the top a cornice molding can be used for both carry a logo or hide a lighting system. ...The components of...

Use with 2mm depth polycarbonate shield.

... fixture with 10 M6 x 20 mm bolts, T-nuts, and an M6 hand tap on a Taig DSLS3000 mill. The version 2 design allows easy access to T-nut bolts through all four plates, facilitating mounting and dismounting without disassembling the fixture entirely.

Panel constructed from one meter square sheet of translucent polycarbonate material.

Print settings include 0.5mm layer width, 0.3mm layer height, 265°C nozzle temp, 130°C HBP temp, 30-60 mm/s print speed, and warping prevention techniques. ...It's also crucial to dial in print settings on a calibration cube before attempting real...

For the first time, we are introducing polycarbonate material as a new addition to our solar water heater range.

... The screws used are the 8 x M1.6 x 5mm screws. Note that transparent polycarbonate used in the Ultimaker frame is very fragile compared to black, which is highly resistant. ... Visit https://www.facebook.com/Microdure/ for more information.

The lightweight and airy architecture of the 90mm frame was made possible by the solidarity and rigidity of the polycarbonate. Be very cautious when flying with other filaments. Polycarbonate Ultimaker 90 mm frame spacing with a sp course evo flight...

I designed a robust polycarbonate front door for my Ultimaker 2 Extended from scratch, utilizing CAD files specifically tailored to the machine's unique requirements. To create this custom design, I modified the existing files for the standard...

I use to set the outlet of the heatsink to 100 °C, which is still fine with the bowden tube and it gives a minimum of about 60°C on the edges of the buildplate. It also preheats your material a bit, or cools it when you turn up the fan for PLA...

... 3D formats. ...The native format remains the industry-standard .skp file, while 3dsmax scenes are crafted using 3ds Max 2016 with flawless integration of Vray 3.00. A rustic wood shed boasts a translucent polycarbonate design that catches the eye.

... to its black counterpart, which offers superior resistance. https://www.facebook.com/Microdure/ Print Settings Printer Brand: Ultimaker Printer: Ultimaker Original Rafts: Yes Supports: Yes Resolution: 0.100 mm Infill: Polycarbonate Ultimaker

French retailer 4 Pieds offers polycarbonate chair and stool legs. The Arthur chair leg is a fauteuil, while the Ice chair leg is a chaise. Both have a trapezoidal shape. No noise-reducing foot pads from this vendor fit. I designed them using...

Polycarbonate chair and armchair glides from the French store "4 Pieds". Armchair model Arthur Chair model Ice The legs of these armchairs and chairs are trapezoidal in shape. No commercially available noise-reducing pads fit. I designed them with...

The light and airy architecture of the 68mm frame has been made possible due to the solid integrity and stiffness of the polycarbonate material. Be very careful in flight with other filaments! Frame: Polycarbonate, 68mm center distance, mini...

After requests, here is the version of the classic tiny whoop x 68mm.\nThe ultra-light and airy architecture of the 68mm frame is made possible by the strength and stiffness of the polycarbonate material.\nBe extremely careful in flight with other...

The airy and light architecture of the 90mm frame was made possible due to the solidity and rigidity of polycarbonate. Be very cautious when flying with other filaments. Polycarbonate structure Ultimaker 90 mm pitch with a flight controller sp...

The solid and sturdy architecture of the 68mm frame has been made possible by the exceptional strength and stiffness of the polycarbonate material.\nBe extremely cautious when flying with other filaments in flight.\nThe frame is constructed from...