6 key macropad 3d models
438431 3d models found related to 6 key macropad.
thingiverse
Pretty handy, but cool, wall-hangable hex key holder/organizer for the semi-random collection of Craftsman allen keys I had scattered everywhere. You can print however you want - I didn't use supports and you can see where the filament is a little...
prusaprinters
Full writeup and software: https://github.com/potatoworld/3x3-Control-Pad This is a simple 9 key + 2 encoder macropad that runs on a Pi Pico. Total build cost is under $30 if you shop smart. The case is 3D Printed and held together with magnets...
thingiverse
Customized version of https://www.thingiverse.com/thing:1783765 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1783765
thingiverse
This is a remix from thing https://www.thingiverse.com/thing:4876853 to accommodate the Adafruit MacroPad RP2040. ...You can use the MacroPad with the backplate or without the backplate.
thingiverse
Made a case for the Adafruit Macro pad. Works great with little support needed. You'll need to get some M3 x 10mm long Socket Head Cap Screws. It can take up to 12mm but they're the max. Leave the backer board in, I did it this way so it...
cults3d
Case for the 3x4 Macro Pad sold by Boardsource. USB ALIGNMENT To align the usb from the elite-C to the hole add 4 additional spacers on each corner. Refer to the last image in for detailed instructions. ... Note The fit might be a little snug.
thingiverse
Hardware Needed: * ESP8266 / NodeMCU * 2 x 300 ohm resistors * 2 x Common Cathode RGB LED * 2 x Novelkeys The Big Switch * 3 x Pairs of 3-pin JST connectors * 4 Rubber Feet Print with low infill, supports on for the main...
thingiverse
A wireless connectivity module for pairing with the 3D Conexxion Wireless Spacemouse, designed to integrate seamlessly with mechanical keyboard switches and a Pro Micro controller. The Spacemouse securely attaches in place and can be swiftly...
thingiverse
This is a simple case for the KPrepublic BM16a. It's angeled at 7 degrees like the BM60 Case I designed. It has enough space for foam or other dampening material. ... I used M1.7x6mm screws.
thingiverse
Ploopy Nano + BDN9 (I don't have a BDN9) Macro pad dimension area: Nano_BDN9.stl - 73.5mm x 73.5mm x 15mm Nano_BDN9_v2.stl - 74.1mm x 74.1mm x 15mm Ploopy Nano + YMD09 QMK Nano_YMD09 - 10.4 degrees of tilt, no access to reset port ...
thingiverse
Case for the 3x4 Macro Pad sold by [**Boardsource**](https://boardsource.xyz/store/5ecc2008eee64242946c98c1). **USB ALIGNMENT** To align the usb from the elite-C to the hole add 4 additional spacers on each corner. Refer to the last image in...
thingiverse
Designed it to fit the KBDFans Zeal PC Switch Tester V2 found here: https://kbdfans.com/collections/zealios-switches/products/zealpc-switches-tester The cutout is designed for a pro micro with USB Micro. This is a simple design. ...Basically...
prusaprinters
Hardware Needed:ESP8266 / NodeMCU2 x 300 ohm resistors2 x Common Cathode RGB LED2 x Novelkeys The Big Switch3 x Pairs of 3-pin JST connectors4 Rubber FeetPrint with low infill, supports on for the main enclosure.Further notes on GitHub for EspHome...
thingiverse
require 3Ø *3mm circular magnet x 12ea rp2040 zero 1n4148 x 10ea mx switch x 10ea wires I printed it with Black resin from JLCPCB(SLA). I posted the assembly process and the process of installing kmk firmware on my blog. ...It's written in...
thingiverse
After months of development, my team and I are pleased to present to you...this tiny little wedge. I didn't love the visibility of the LCD with it flat on the PCB, and I felt it'd be much improved with a bit of an angle to it. USE AT YOUR...
thingiverse
Personalize, dust-proof and enclose your Púca! --------------------- This is a sandwich-style 3D printed case made for the Púca by FFKeebs. https://ffkeebs.com/collections/puca It can be adjusted to have either a 7 degree angle or to lay...
thingiverse
Customized version of https://www.thingiverse.com/thing:54024 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=54024
thingiverse
Designers craft a custom-made macropad plate and base to perfectly accommodate the PCB from the Boston 2018 Keyboard meetup within a compact Altoids tin enclosure.
thingiverse
made a case for the Adafruit Macropad RP2040. added room for 2 extra adafruit encoders and a 14 segment featherwing display, so it will fit most featherwings where the top display is. ... Included fusion 360 file and STL
thingiverse
Revamped Design A custom macropad plate and baseplate crafted specifically for the PCB from the renowned Boston 2018 Keyboard meetup, now perfectly encapsulated within a durable Altoids Tin casing.
thingiverse
To build it, you won't need any hardware - just slip fit the two parts together with the macropad in between.\r\n\r\nThere are two variations of the bottom part: one that sits flush against the switch plate and another that rises up to align with the...
thingiverse
Hello, This is a design for a macropad that I bought on Amazon for a Friend, He wanted a StreamDeck and I made this to make it work a little bit better for him. I struggeled with the time to gift it thats why in the pictures apprears the issues on...
thingiverse
Follow 3D Print Kings on Instagram and share a photo of your print by tagging us @3DPrintKings!
cults3d
please follow us on instagram & tag us if you printed it:https://www.instagram.com/3dprintkings