6 key macropad

40 Watt Explosion Proof Low Profile LED Fixture - 5,400 Lumens - 347V - Class 1 & 2 Div 1 & 2
grabcad

The LED assembly is protected behind a tempered borosilicate glass tube that is protected by an aluminum wire guard to prevent from accident damage to the light fixture.Measuring only 6.89" in width, this fixture takes up half the surface area as a...

Galactus Bust 3D Printing Figurine | Static
gambody

You can pay with PayPal or your credit card.Also, you may like other Busts 3D Printing Miniatures as well as 3D Miniatures Marvel and Villains._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set...

MegaGRRL Desktop - Real Hardware YM2612 VGM Player - Casing
thingiverse

Check the "MegaGRRL-Construction.jpg" picture for part orientation, the slider and arm can only fit in correctly in one orientation 6. To test fitment, attach the D-Pad to the D-Pad control arm to check that they fit together, aligning the peg with...

The Universal Kitchen Rack
thingiverse

There’s also a four-post style (“V4P”) that can hold items a little over 6 inches in diameter. 2. A two-post vertical rack is not recommended because the weight of the items in that slot would be applying a cantilevered load on the divider, which...

Prusadusa and the sands of time clock
prusaprinters

Secure the watchface on the top using the 6 remaining M3 screws.24.Fill the plate of the watchface with fine-grained sand until you've reached the line on the central cone(about 2-3mm).Set your 10mm steel ball onto the minute_hands magnet and the...

DIYLaserBed (RevB)
thingiverse

![DIYLB_rail_assembled](https://raw.githubusercontent.com/hotwolf/DIYLaserBed/master/revB/assemblies/DIYLB_rail_assembled_tn.png) [Top](#TOP) --- ## DIYLB Crank Assembly ### Vitamins |Qty|Description| |---:|:----------| |2| Ball bearing 608-2RS...

Ikea Samla 45l Filament Buffering Dry Box
prusaprinters

Spools, Buffers and Desiccant containers all can easily be loaded from the top of the box for ease of operation.Main CharacteristicsUses Ikea Samla 45l as base box as it is quite cheap and available almost everywhere.Fits at least 5-6 standard 20cm...

Drone SRX (only zip ties!) English Available!
cults3d

THE ELECTRONIC PARTS I'M USING (skip that section if you want) Motors : Racestar 2306 2400kv (55.50$ on Banggood) Flight Controller/ESC Stack : Diatone Mamba F405 MK2 F40 (67$ on Banggood) VTX : Eachine TX-805 (21.50$ on Banggood) (or TBS stuff,...

Cavalieriho princip
prusaprinters

1 - Matematická úlohaŽáci dostanou zadánu matematickou úlohu – Z kolika destiček o výšce 4 mm, sestavím kvádr se čtvercovou podstavou o rozměrech: a = 6 cm, a objemu V = 288 cm3 (rozměry lze upravit )Rychlejší žáci, či skupinky žáků, mohou...

GeitPrinter
prusaprinters

(main extrusion length times five) 13x 20mm extrusion corner brackets 1x 400x350x10mm wooden plate (can be metal, too) 2x GT2 driver pulley 60 teeth 8mm bore (with 2 set screws each) 3x GT2 driver pulley 20 teeth 5mm bore (with 2 set screws each) 8x...

Self winding pendulum clock (climbing weight for weight driven clocks)
thingiverse

... size="3">About the winding mechanism: It has been working for about a half year, no sign of wear, battery is still in good condition. :) About the clock accuracy: 6 mins gaining per week, details are here: https://www.thingiverse.com/make:929621

Kyosho Ultima RT5 Chassis Service Pack "REV7"
thingiverse

Edit: 15.6. - Studied possiblity to use Team Associated RC10 T6.2 Front lower suspension arms in REV7. Straight arms are direct swap with some extra shimms used and with T6.2 hinge pins (which are just slightly longer than RT5). Longer shock...

simplyRetro Z5 ( RetroPie / Emulation handheld )
prusaprinters

The audio jack plug should be press fit.Battery MonitorFor this step you will again need a bit of the Stripboard, the MCP3008, two 6.8k and two 10k resistors.Again make sure to do the cuts on the Stripboard, before you start soldering. Solder...

(V1) For BIQU B1 - DIY Enclosure - Remix of Prusa's IKEA Lack Enclosure - with extra doors (opening on 3 sides)
prusaprinters

... a 0.6 nozzle, as explained in a video I’ll link in the details. When you glance at the print times on my Cura screen shots, bear in mind my 0.6 emulation, and I’m using a dry box so no need for printed spool holders. Category: 3D Printer Accessories

MCS - Multi Color System for Prusa MMU3
prusaprinters

The sides are different..4 or .6 nozzlePETG (for strength)20% infill3 perimetersup to.35 layer heightno supportsPrusa Buffer versionThis prints with snug supports to support the peg on the end:.4 or .6 nozzlePETG (preferred) or PLA20% infill3...

130 Elektra scaled one in four million
thingiverse

G-type. Density: 1.55 g/cm3 Dimensions: 262 km × 205 km × 164 km Model scale: 1:1x106 (26cm) 1:2x106 (13cm) 1:4x106 (6.5cm) References Shape model of asteroid (130) Elektra from optical photometry and disk-resolved images from VLT/SPHERE and...