5mm to in 3d models

Made this adapter for my nilfisk vacuum (Buddy 2) hose to fit my dust cyclone.Print with the threat end up and add a brim.Outer diameter 50,5mm:OBS i always make the model slightly larger, so that i can take a heatgun to it, and make a pressfit of...

This is an adapter for using lego threads on a REV shaft, 5mm. ...it is used for installing lego threads on robots, main and planned use are for ftc. designed and published by ftc team Cavalo Vendado (16786) not associated to LEGO or REV

This is a 8mm Lead screw to 5mm D shaft Coupler (Stepper motor). Specifically designed for a dolly Mk2 Prusa Z axis. The coupler has holes for two M3 locking screws, one for the D shaft and the other for the Lead screw. ...Do not over tighten the...

Mounting an AfroFlight Naze32 board or other 30.5mm configurations to frames with 45mm mounting hole setups is a breeze. The holes are precisely sized at M3 / 3mm diameter, allowing for smooth installation without threading. ...Inner studs pair...

Self-Aligning Stepper Motor Adapter A precision-engineered adapter designed to connect a 5mm stepper motor shaft seamlessly with an 8mm trapezoidal lead screw, ensuring maximum rigidity and stability. ...Perfect for applications requiring precise...

This is a narrow cleaning tip designed for Zelmer Jupiter iwth tapered end with diameters of 30,2 mm at the bottom and 32,5mm at the top. Walls were optimized for 0.4 mm wide printing and being 1.6 mm thick should be more than strong enough for...

This is a narrow cleaning tip designed for Zelmer Jupiter iwth tapered end with diameters of 30,2 mm at the bottom and 32,5mm at the top. Walls were optimized for 0.4 mm wide printing and being 1.6 mm thick should be more than strong enough for...

... the 25mm mounting holes. ... Two versions here, one with and one without standoffs to help with spacing on your FC. Walksnail system will fit on top of an FC with 30.5mm mounting holes but at a 45 degree angle to allow for access to the FC screws.

I designed this adapter to fit a few of my tools with smaller dust extraction ports. ...It is tapered on both ends for a secure slip fit. The profile is smoothed to prevent additional noise and aid in printing.

Now add nema17 Y axis motor with trapezoid rod (in my project it's 8x300mm one).\n\nPart 5:\n\nhttps://www.youtube.com/watch?v=DEYo9oCoOQM\n\nPrint 1 of XAxisMotorFrame.stl.\nRemove 3 aluminum extrusions (both from sides and front one), take out top...

Adapter for the NIB Rainbow G12.5mm lens for micro four thirds cameras. Since this lens normally doesn't fit to standard c-mount adapters, I created a custom lens mount, which incorporates threads for focusing. For a 12.5 f1.4 lens it has pretty good...

Customized version of http://www.thingiverse.com/thing:91035, available at http://www.thingiverse.com/thing:102040, was created using Customizer with the following specifications: Resolution at 25; Set Screw Nut Diameter at 5.5mm; Set Screw Nut...

12 gauge Flare adapter for 26.5mm older surplus flare guns

L-Bracket Support, for Wardrobe or Similar Shelves, 5mm Diameter Pin.

To be printed with the threaded side upward, using supports, to ensure the O-ring recess face flatness. Thread length 9mm. File identified as BSPP G1:4 5-7mm.stl **UPDATE 27/Nov/2021** -Added a 1 mm chamfer at the base for strength reasons. ...

It is designed for 14,5mm 2,5" disk. ...You may fix the floating side of hdd with tape.

Meterstab (Zollstock) Halter adaptiert für eine Lochwand mit 15mm von Mittelpunkt zu Mittelpunkt der 3.5mm löcher

This is an adapter for 3.125mm to 5mm axles. ...To print it I recommend to start with default settings and increase/decrease flow depending on how well it fits (optimally it wouldn't have any noticeable play). There are three versions:Just a...

This is a versatile adapter for combining 5mm hex shafts with Actobotics servo blocks, allowing for seamless integration of these two systems.

The standard configuration calls for a 16MM VTX mounted directly onto 30.5mm stand-offs, allowing for effortless integration and streamlined flight performance.

Saw this great design but when I measured my fin size it was 3mm so i decide to use the design and make a taper for the first 3/4 of it.

I hope you looking for this. ... There is 2 files, one is normal, the other is with a hole. An M2x10 screw should be screwed into the hole to strengthen the base. ...The part is not perfect, but when it breaks, print the next one.

I swapped out my 5mm tooth on the cube, but it didn't fit quite right, so I busted out the calipers to get a closer look and found it was actually a bit over 11mm, which meant I had to make some adjustments. I added another tooth, moved it down by...

Customized version of https://www.thingiverse.com/thing:44078 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=44078 Instructions Using the following options: D3 = 3.75 D2 = 5.25 D1 = 24.875 SLICES...

Customized version of http://www.thingiverse.com/thing:299663 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=299663 Instructions Using the following options:...

This remix is smaller than the original in order to be placed easily in the hole. ...The insert's nut is also removed to be able to screw the rotary after mounting it. Category: DIY

This remix is smaller than the original in order to be placed easily in the hole. ...The insert's nut is also removed to be able to screw the rotary after mounting it.

A versatile mounting solution that enables seamless integration of a QuadCopter flight controller with 30.5mm mounting hole spacing into a standard 45mm mounting hole configuration, boasting an ultra-lightweight design and a mere 2mm thickness for...

Den Ring sollte man auf den Kopf stellen und kann ihn dann problemlos drucken.  English Description:This adaptor can be used to adapt projection lenses with 62.5 mm rear diameter to Sony E-Mount.It is was tested with a 105mm...

The NEWA water pump adapter 12/4.5mm is designated as part number 1 on the diagram. ...The original component is available at https://www.thingiverse.com/thing:3716591, and a longer alternative adapter measuring 48mm can be found at...