54mm dosing funnel 3d models

Funnel for filling 54mm portafilter with coffee to prevent spillage. Tested with Sage/Breville portafilter.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p class="detail-setting printer"><strong>Printer: </strong>...

This funnel attaches directly to the bayonet of the portafilter holder, allowing for easy tamping through its open design.\r\n\r\nThe funnel is specifically designed to fit grinders with limited vertical space, featuring an inner diameter nearly...

The funnel especially fits to grinders with limited vertical space. The inner diameter is close to the portafilters diameter and therefore it fits perfect in a Mahlkönig K30 Grinder. UPDATE: Added two reinforced derivates (L and XL) which may last...

Rather than using "math" and "measurements" I offset the original funnel in 1 degree increments and hoped for the best. The picture above is 8 degrees which is too much. If I printed again I might go for 6 degrees. ... Try your luck and reply back...

Rather than using "math" and "measurements" I offset the original funnel in 1 degree increments and hoped for the best. The picture above is 8 degrees which is too much. If I printed again I might go for 6 degrees. ... Try your luck and reply back...

Here is my version of a single dosing hopper for the Baratza Sette 270: I designed it to perfectly complement the grinder's sleek lines and intuitive design. For the lid screw, I opted for an M2 x 20mm screw that provides just the right amount of...

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Please print with food safe filament like PETG. Matching neodym magnets:Shape:discDiameter (D)5mmHeight (H)5mmTolerances+/-0.1 mm           May not fit to all VST-Baskets. Please check the outer diameter, should less or near 70mm. ...(see comments)

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

<p>Attachment to porta filter is realised with eight 2x4 mm cylinder magnets.&nbsp;</p>

<p>Please print with food safe filament like PETG.</p>

This is very simple design, it works so I might was well upload it. No support needed. ... Pop this on top of your 51mm portafilter basket to make it easier to load coffee.

Print at 0.2mm StructuralYour choice of filament

Allows for reduced loss of bean when grinding. Holds on snug to the portafilter to avoid any potential accidental spillage. V2 - Requires less supports. ...Much easier to print than the original version.

Use 5 x 3 mm magnets, I used ones from Apex: https://www.apexmagnets.com/magnets/5mm-x-3mm-disc-neodymium-magnet Please see my other designs for the Breville Bambino Plus: Shot Glass Pedestal and Extraction Mirror:...

I could not find a dosing funnel for my Breville Bambino Plus 54mm Portafilter (PF) which fits into the PF holder of my Smart Grinder Pro. The ones I have tried are too tall so I had to tilt the PF forward a little just so it goes through the cradle...

I could not find a dosing funnel for my Breville Bambino Plus 54mm Portafilter (PF) which fits into the PF holder of my Smart Grinder Pro. The ones I have tried are too tall so I had to tilt the PF forward a little just so it goes through the cradle...

58mm Dosing Funnel for Breville Barista Max (VCF126X) and Max+ (VCF152X) Espresso Machines. Print upside down without supports. ... Two versions, choose yours: - 0.6 nozzle, 0.4 layer height, 0.6 layer width TESTED - 0.4 nozzle, 0.2 layer height,...

### Features - Contacts the basket exterior, since internal funnels leave a void in the coffee grounds - Friction fit to hold basket in place, since magnets barely stick to 304 Stainless Steel - Funnel doesn't have to be held in place, can be flipped...

haven't printed it yet

made 58mm wide to fit my solis coffee grinder, and extended to catch coffee crappy edit made with tinkercad, but it works

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Coffee grind adapter for Graef CM 800 and the ECM portafilter suitable for the ECM aluminum tamper station. ... Kaffeemehladapter für Graef CM 800 und den ECM Siebträgern passend für die ECM Aluminiumtamperstation

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738