52mm gauge 3d models

52mm Gauge hole plug

52mm gauge holder

Simple cap to fill a hole for a 52mm gauge.

Replace the center air vents with three 52mm gauges. ...It is recommended to cap off the AC hoses before removing the center panel.

Twin 52mm Gauge pod will hold any 52mm Gauge, Turbo Boost, Vacuum, Volt, Oil Pressure etc etc , this pod is based on the Rovotech style (not exact Rovotech) my design. ...This is designed to fit with 3M type double sided tape not screws making it a tidy...

52mm_Gauge_Bracket Just minor adjustment to make a base model to support 52mm Gauge. I needed to make a bracket to glue on dash compartment wihout loossing an entire 1Din space. May need to adjust holes with file or 4mm drill. ... Enjoy ;)

A handy accessory for any electronics enthusiast is the 52mm gauge stand. ...This versatile tool serves as a reliable test bench, perfectly accommodating both a boost gauge and a multimeter placed conveniently on either side.

52mm gauge pod for all automotive use, snug fit from printer no need for sanding. ...20mm hole at the back for hose and wiring, can be mounted with double sided tape or can be drilled into base.

This is an aircraft cockpit inspired gauge bezel for the Autometer 52mm gauge series. It insets the gauge for a more flush mount look. The mounting holes are designed for M5x0.8 cap screws. ... The retainer holds M5x0.8 nuts so the bezel can be...

... ... Oem part number: 45286-53901 Valid for Toyotas and Lexus models: Is200/300 Altezza Gs300/340/400 Mark 2 Celica 52MM Gauges pod on ignition barrel cowl plastic trim surrond stalk column. Material: PLA, recommended ASA Printing: 3h with supports.

This rugged 52mm gauge pod mount is specifically designed for a RA24 Celica, providing a secure and precise mounting system. ...A sturdy threaded hole allows users to easily tighten each gauge into position, accommodating any 6mm x 1.0 thread pitch bolt...

Print this in ABS with all walls so that its still strong being this thin. ...Drill a hole in the back for the wires you need. This is for a autometer 2 and 1/16" gauge. I'm sure it fits all 52mm gauges.

Valid for Toyotas and Lexus models: Is200/300 Altezza Gs300/340/400 Mark 2 Celica 52MM Gauges pod on ignition barrel cowl plastic trim surrond stalk column. Material: PLA, recommended ASA. Printing: 3h with supports. ... @xdash_211 If you liked it...

Volvo 240 52mm Gauge fits 1din spot

Replace your center vent with this to put in 2 52mm gauges. ...Still functions as a vent in the middle.

These OEM vent grill replacements are CAD designed to simply pop-in to the stock vent in your Car. ...They house 52mm gauges. EASY TO PRINT. ...NO SUPPORTS Not for commercial use.

This is a 52mm gauge pod designed for the Chevrolet Corsa B, sold in South America, and also compatible with the Vauxhall Corsa B in Europe and the Chevrolet Chevy in Mexico. The pod fits seamlessly into its original location, mimicking the...

Nice simple 52mm automotive gauge pod visor hood. Keep the sun off your gauges and make them more easy to read! ... 60mm length version 50mm length version

... jumble of aftermarket gauges in my 1989 Isuzu Amigo. ...Will accept your standard 52mm gauges. But, like, six of them. I designed it to angle each column toward the driver (left) side when mounted in the center of the dashboard. ...Thanks for looking!

These OEM vent grill replacements are CAD designed to simply pop-in to the stock vent in your Car. ...They house 52mm gauges easily printable from 3 pieces. Scale it in your slicer according to your needs. ... Not for commercial use.

I'm excited to share this innovative product with you - a specialized, 52mm gauge support designed specifically for the iconic Volkswagen T2 dashboard. This clever accessory is perfectly positioned to take its rightful place on the third hole of your...

Designed to bolt onto the back of the tachometer housing, I designed this mount to hold two 52mm gauges next to the tachometer. ...The fit on the right side is fairly tight, at least on my Countryman I found the tachometer was not totally centred in the...

Mount a 52mm gauge into your car's dashboard using this bracket. If leads or illumination lack clearance, modify the middle shape of the bracket (refer to Sketchup file). To print, use nozzle 0.35mm and layer height 0.175mm with 3 solid layers at the...

Two 52mm gauge pod mounts I made for my 98 Jetta TDI. Sorry for the bad photo, I'll take another in daylight. (gauge backlights are being changed out for green to match the dash) One goes where the heated seat buttons would go but you must cut away...

Two 52mm gauge pod mounts I made for my 98 Jetta TDI. Sorry for the bad photo, I'll take another in daylight. (gauge backlights are being changed out for green to match the dash) One goes where the heated seat buttons would go but you must cut away...

Simple old school style gauge bracket for Autometer 52mm Z series gauges. ...Will probably fit others.

An excellent gauge pod hood for 52mm or 2" automotive gauges. Keep the sun off your gauges and make them much easier to read. Easy to print! ... Lets go racing!

a simple 52mm right angle gauge mount made for a fast yet sturdy print. ... 3mm holes added in base for easy mounting

This is a straightforward gauge retaining clamp, typically used in conjunction with customized gauges. ...Given my tendency to misplace items, I began creating these clamps through 3D printing.

beautiful design fits perfectly for 52 mm gauge pods message me for costume designs