5015 ender 3d models

- You might need some dremeling/filing the stock ender 3 carriage, since it has some interference with the Phaetus nozzle. I didn´t designed this project to work with spacers, but it might work. Try at your own risk. - I designed it to work with...

16/02/2022 Major Update: Titanator Version 2 Changes: Reduced the number of parts Significantly increased structural rigidity The bed leveling sensor has been completely redesigned Added support for Volcano hotend Fixed the gaps between the...

I've remade this thing from scratch, and now it's compatible with bltouch sensors. If you'd rather use an ezable sensor, just stick with the original model linked above. I've also included a solidworks file for your convenience. To set up the...

I really liked how slim the original RS fan housing was, but it didnt want to fit with my direct drive mount. So I took 5 minutes and chopped some bits off to make it fit. I also filled in the bl touch mount spot, so you can just slap a stock mount...

It is a remix of the hero me gen 7 single 5015 fan duct to make it fit for a Creality Ender S1 & S1 Pro. Most other Ender 3 S1 & Pro ducts are routing them to the right side of the CR touch module; however that results in a narrow air channel...

Fantastic hotend that you can push to the limits of this machine . ...never clogged once or any heatcreep.

This is currently a work in progress as I'm just now printing it, I'll update if there's any problems. Use custom supports to not support the inside, only the outside where needed. ... Attention, it has been modified for the Hotend Creality...

This is a remix of the Ender 3 S1 Hotend Fan 4020 Replacement Bracket. This remix mounts a 5015 blower fan instead of the 4020 blower and is further offset from the gantry so that it will clear the x-axis enclosure on Ender 3 Pro and other similar...

Replace noisy hot end fan on the Sprite Extruder with a quiet 5015 blower fan.This is a remix of the Ender 3 S1 Hotend Fan 4020 Replacement Bracket.This remix mounts a 5015 blower fan instead of the 4020 blower and is further offset from the gantry...

This is a remix of four essential components needed to ensure your Ender 3 and compatible printers have a good E3D V6 mount with Direct Drive BMG extruder (without Bowden), which includes a 40mm fan mount directly on the V6 clip item and a dual 5015...

Most compact hotend and part cooling system for Ender 3, Ender 3 Pro, Ender 5, CR-10, and other Creality compatible printers. Weighs less than the original metal housing, approximately 40 grams. Engineered to minimize unnecessary cooling of the...

I've remixed a bunch of different ones but decided I'll just make a purpose-built one.You could also use this as a bowden setup!UPDATE AUG 22, 2022:Added a BLTouch mount option that fits the Ender 3 V2 gantry.UPDATE NOV 22, 2021:By request, I've...

Weights less than original metal housing, around 40 grams. Designed to reduce unnecessary cooling of heatblock and printed part by 4010 heatsink fan. It does not reduce the air flow generated by both fans as most of the designs do resulting in...

I needed to remix a Satsana to fit my Ender 5 with the direct drive adapter kit and a Creality Spider v3 installed. None of the previous shrouds fit my set up just right. ... I printed with minimal painted on supports as shown in the picture.

The following is the changes I made to the Fan Duct Corrected the width of the 5015 Fan port as it had a gap that would allow air to escape Added support for the CRTouch as the cable outlet is in a different location. I had to remove the center hole...

This is a custom cooling solution for an NF-Crazy Plus hotend on an Ender 5 Pro. The NF-Crazy Plus is a Mosquito clone that is wider than the original Mosquito, but also mounts using the stock Creality mounting solution rather than the...

I needed a duct and didn't like the bulkiness of the ones available so i made one a little more compact. ... Its definitely still a work in progress.

Comes, with a slot to use a zip tie to secure cables neatly (i couldn't be bothered in the picture, but it is there to use)Uploaded version minorly different to photographed, the extra m3 nuts to lower the bltouch aren't needed in the model...

I no longer have the V2 Neo, but these were the last changes I made to these shrouds which gave me the best look/fitment.

Refer to original creator for more information. ... https://www.thingiverse.com/thing:3433290/files Thanks to https://www.thingiverse.com/tunnelcake/designs

CR Touch version of https://www.thingiverse.com/thing:5318363

<p>Refer to original creator for more information.</p> <p><a href="https://www.thingiverse.com/thing:3433290/files">https://www.thingiverse.com/thing:3433290/files</a></p> <p>Thanks to <a...

A versatile zip tie system was installed, providing adjustable support for the hotend cables. ...Three distinct options are now available, including rear, 45-degree rear, and 45-degree forward configurations, each designed to optimize cable management...

Edited JoshLangsford's design to fit a 20x40mm cooling fan, as well as made the ducts removable to make it way easier to print. It's not perfect and it's a tight fit, but it does work and it's very minimal for a dual fan duct. The current design...

This is a remix from the original thing found here: https://www.thingiverse.com/thing:5867916 Please refer to that link for installation instructions. I recommend printing this in the orientation of the picture from Cura, supports set to touch...

This is my 3rd attempt to design an upgraded fan duct for my Ender 3 S1 pro (with sonic pad), upgrading from the original to a 5015 blower fan 24v (you can use a 12v with a tension regulator) I tested some fan ducts around, paid or free, and it was...

I remixed this thing to see x bar level according to the bed for when its need some tuning on machine. Also i can track for any misaligments of bar after a period of usage. ...

My nozzle was too close to the bed when Auto Leveling so it would leave a tiny dot of filament at each probe which was annoying for a large print. This is a basic spacer for in-between the BLTouch and the Satsana. ... IMPORTANT: You still need the...

Tapa ventilador para https://www.thingiverse.com/thing:4789305 Dos versiones. ...Sin rejilla y con rejilla