50 sided die 3d models

It's about 320mm cubed (1ft cubed). It's using 210mm, 230mm and 250mm 2020 Series Aluminum Extrusion but should be able to scale to anything (I think), you would just need to alter the Marlin configuration files and get longer rods, belts and a...

https://www.prusaprinters.org/prints/134117-freight-ten-cargo-transport-model-science-fiction Use with your Armoured Shelter https://www.prusaprinters.org/prints/121033-armoured-shelter-terrain-two-models  or carry with the Machina to their...

I printed them at 20mm (4 hours or so,) but they look even better at 15mm.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

Note the treads match in shape the body of the Freight Ten.Superglue the cab to the body to the front grill is overhanging the front slightly (see the images).No print supports are needed.Superglue works best for gluing it together.Did not use...

Always cut the silicone tube at a 45° angle and make sure that it is cut in such a way that air bubbles will be able to flow through it unimpeded. A mistake here will make your system fail to dispense. Fold the wire in the middle, insert it through...

So these process towers were built and deployed to slowly refine the lost minerals and deadly toxins within the atmosphere that have value, instead of allowing them to go to waste within the short lives of the damned, I mean worker's lungs…Print with...

For this very reason the belt path had to be moved 3.53mm to the left so that the block doesn't collide with the motor.Mods should give about 1mm of clearance on the sides and bottom of the MGN12C blocks.On the left, the MGN12C block protrudes 3.5mm...

I made them on TinkerCad.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

For hell's coming in the “White Desert.”Designed on Tinkercad.No supports required.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

Solder the headers onto the control PCB so that the standoffs are on the opposite side to the conductive pads. 2. Solder two tactile buttons onto the control PCB into the pinholes labelled ST_* and SL_*. 3. Solder the TeensyLC onto the headers. 4....

... Put one ball in each of the little cups on the left side of each of the counting trays. Those balls are counterweights that make sure that the counting trays will reset to their normal orientation (leaning to the left) after they empty their balls.

For post processing pics please go to https://www.thingiverse.com/thing:4606971 Note that the embedded nuts go on the inner side for this model while they go on the outer face for the boat project due to access issues. The boat model also has an...

Ready to pump your promethium, sweet crude, or whatever lights up your day!Designed on Tinkercad.Enforced supports are required on verticle pipes (see files).Superglue the valve handles.Start pumping that...

https://www.prusaprinters.org/prints/134117-freight-ten-cargo-transport-model-science-fiction Use with your Armoured Shelter https://www.prusaprinters.org/prints/121033-armoured-shelter-terrain-two-models  or carry with the Machina to their...

Use for scatter terrain, on your model railroad, in a diorama, or whatever gets your motor running.Two sizes are included within the files. No support required.Easily resized.Assemble: super glue the top frame to the posts. Designed on...

 The print shape at the 2 magnetic connection points gives the feed into the extruder a more vertical route  while also removing the tight bend you often see on the K1 series at the point the PTFE normally enters the extruder.My preferred way of...

If you're printing the 6x3mm magnet Top body version, right click and pause @ layer 9.20 mm.This will be a pretty tight fit, you will have to press down decently hard on all corners ensuring it is flat. I like to place the side that will be...

Assuming I did my math right you will generally want to start with about 40-50mm of exposed inner slide and tune from there. Now cut a 16” long piece3 of the same ½” schedule 40 PVC pipe and fit it into one side of the tuning slide inner mount. Fit...

As I'm often getting asked about this and finding it hard to explain at the moment. The rod length of the rods effect the side ways x and y in its movement with the settings of "DELTA_DIAGONAL_ROD". That's why your high is correct as the system works...

The gear end is the front.No supports are required.Superglue works best for gluing it together.Will scale easily if you want a larger or smaller...

If there is a down side desiccating the air running through the system does cost a little energy, so reducing the performance of the cooler a little, but I don't expect that to be significant. The rest of the Bong_Bong_Aircon is all about...

My bed has wings with holes on the sides for mounting. I re-designed the bottom corners to be able to mount the bed using the wings and into the corners. Detacheable motor frame. The Kossel Mini, Kossel XL and the v1 suffer from the same annoyance...

Operating directly from a 9 V battery at 150% of the maximum rated voltage seemed unwise so I incorporated a buck converter to drop the battery voltage to 6 volts.= = = = = = = = = = = = = = = = = = = = =BILL OF MATERIALS:3D Printed...

Glue each in place with Superglue.No print supports are needed.Superglue works best for gluing it together.Did not use “Variable height” layers, but it will smooth the angles on the cab if used (adds time to the print).Will scale up easily if you...

Is there a down-side? Not that I'm aware of but this hot end isn't rated for Nylon... a shame but no biggie as I now have a large core-xy printer with a huge nozzle for banging out such prints - the Anycubic printer only has to cope with the fine...

The sensors I bought have Dupont connectors on the board side, but the cables are way too short anyways, so I will be creating 3-wire cables with JST-XH connectors for those as well. So adding to the hardware list: 4 (or 5) 3-pin JST-XH sockets 2...

Take what's theirs and make it your own! More Armour!Demolior Class Heavy Tank - https://www.printables.com/model/135967-tank-demolior-class-heavy-deathhead-ii-model-scien Scopulus Class Heavy Tank -...

Из за чего приходилось постоянно вытягивать припой второй рукой, что не так удобно и быстро.Parts links below - Материалы которые я использовал: Micro Mini N20 Gear Motor DC 3V -6V Li-polymer 3.7v 200mah 502025 Type-C USB 18650 Lithium Battery...

See the Create your own section for more information about building a custom model.This project uses the the T-Nut mounting system created by @6d6178 to attach to the pegboard itself and uses BV3D's method to print indicators on the first layer in a...

If you need a two-post vertical rack, and the items being stored in the rack are very lightweight, a horizontal TUKR could be turned on its side get a two-post vertical TUKR. 3. Determine the height of each slot, which will be the height of the...