5.25 bay fan 3d models

So, I ditched the external radiator and decided to go for an internal mount by throwing out all the HDD bays it had in the 5.25" bays and free up the area for a 240mm radiator.Digged up the 120mm fan drawings and went to town in the Fusion360. Made...

5.25" Drive Bay Fan Cover for 120mm Case Fan

I only had two spare 5.25-inch bays available and a leftover 120mm fan from an old power supply, so I devised this innovative design. Operating at 7 volts, it draws quite a substantial amount of air into the case while maintaining a remarkably low...

I only had two 5.25" bays free and a spare 120mm fan from an old power supply so I came up with this design. Running at 7v it pulls quite a lot of air into the case and is fairly silent. Screw two vents one to either side of a 120mm fan and use...

This allows you to suck/blow air out a front bay using a 120mm. ... two versions are avaliable, Fan above bay or fan below bay.

I had searched for a good 5.25" drive bay 120mm fan adapter for my older Antec P180 case and couldn't find anything that would work well enough so I made this. Designed to snap into where the block off plates snap into, its a direct fit for this...

This is a custom fan mount designed specifically for the Lian Li PC-Q08 case, utilizing three high-performance 40mm fans that provide exceptional airflow. ...The fans are secured in place with sturdy 4mm screws, while the entire assembly is easily...

5.25 Drive Bay Fan Cover for 120mm Case Fan I will upload more designs, for those of us who like to modify our old cpus

It WILL take a lot of time to recompute - it took about a full minute on my machine.The other FreeCAD design file (5.25 bay_cover_fan.FCStd) I used for designing the rest of the parts. I exported the mesh I was happy with and designed around it. This...

A compact and efficient solution for superior PC cooling is provided by this 3x 5.25-inch fan bay, featuring a spacious 12cm design.

Made for cases with two, or more, 5.25" bays. You can mount two standard 70x70mm fans. It's mounted to the case using 4 or 8 M3 screws. The measurement were used from provided pictures found on the internet. NOTICE!!!: The height of 85mm might...

It uses the two 5.25 bays typically only available in a mid-atx case and positions the 120mm fan at an angle suitable to fit but still flow air cleanly. Results were evident when I measured ambient internal temps before and after, there was a 16°c...

This adapter attaches to the face of the enclosure, so bays are available for installing hard drives and other componentscustomized for my home server case

This mounting adapter is designed for 120 mm fans and is specifically constructed to fit snugly into three standard 5.25" drive bays. It differs from other mounts in that it's not intended to be visible from the outside, thus its compact dimensions.

This innovative design features three strategically placed holes, each accommodating a 40mm fan, to ensure optimal airflow and keep your system running at peak performance. ... With my Print Settings optimized for precision, I've chosen the following...

Server technicians require a solution to install on the front of servers for fan maintenance.

The adapter is designed for a 120 mm fan at the front of the case, occupying three 5.25" drive bays. The fan itself is secured by four M4 screws that are 4 mm in diameter, while the standard M3 screws that come with it measure 3 mm in length,...

An adapter for a 120 mm fan in the front of the case, taking three 5.25" drive bays. The fan is held in place by four M4 (4 mm) screws, the adapter standard M3 (3 mm) screws, the same 5.25" drives use. I was able to hold it in place with M3 screws...

After printing my HD Adapters, I decided to take it up a notch by creating an adapter that allows me to utilize a 5.25" PC bay as a makeshift blower for my hard drives using a trusty 120mm fan. ...Check out the finished product here:...

Could use nuts and bolts or Zip Ties as well.︵‿︵‿୨ ✿ ୧‿︵‿︵✦︵‿︵‿୨✎୧‿︵‿︵✦︵‿︵‿୨ ✿ ୧‿︵‿︵Possible improvements:1 Add the second set of holes in the top and bottom bay.2 Switch to attachable* "arms", will be much stronger if it prints flat. Either...

This adapter fits perfectly into that vintage case featuring abundant space for CD 5.25-inch bays, allowing users to install a highly impressive HDD accompanied by an additional option to mount a powerful 120mm fan for enhanced cooling capabilities.

this fits in place of 3 of the 5.25" CD or DVD drive bays, and fits nicely on my PC. This is modeled to be printed with zero supports, and will print fine. The only slight overhang is the clips, and they printed without issue. Modeled to be...

I needed additional cooling units to upgrade my compact HP desktop PC, which serves as a central hub for routing internet traffic within my home network.

A 140mm fan Holder for 5.25 PC bay. Distance beetwen holes 124.5mm. 4mm holes for fan screws. Side screws 2mm, You can use a ABC screw or try with PC ones. No threads in the holes, you can do it if neccesary with a thread maker. You need 4 free...

Takes up 2 full-size bays (5.25 inch size like older DVD drives). Fan can be mounted as either intake or exhaust depending on your preference. Designed to be printed face-down (this helps get a cleaner print on the front assuming you have a smooth...

A mount for a custom computer fan speed PWM controller. ...A knob for a potentiometer to adjust the fan speed. Fits into a standard 5.25" drive bay. ... Category: Computer

... a custom computer fan speed PWM controller. ...This unit features an adjustable knob that directly interfaces with a potentiometer, allowing users to fine-tune their fan's speed settings. The device neatly slots into a typical 5.25-inch drive bay.

These brackets allow for a 120mm fan to be mounted along with one disc drive in the 5.25" bays. This helps push air to the CPU cooler directly without obstructions like HDD bays.These brackets can be screwed in, or can also utilize toolless mounting...

The designer stripped away the logo to reveal a sleek and minimalist aesthetic.

A 120mm fan bracket for 3x 5.25 inch bays. It mounts with M3 screws just like an optical drive or other 5.25 inch bay accessories.This is a slightly refined version of https://www.thingiverse.com/thing:2446552, with many dimensions tweaked to give a...