5 plus 7 3d models

Ender 5 Plus Tool Holder =================== Remix of https://www.thingiverse.com/thing:3655629 from [Kyle Finnigan](https://www.thingiverse.com/TrigoKlei). It's a tool holder for all Ender 5 Plus stock tools which can be clipped on the vertical...

Remix of the Satsana air duct to allow for the installation on and ender 5 plus carriage without causing a problem with the Y end stop or the belt tab. Pairs with my other file for installing the Mosquito hot-end onto the ender 5 plus.

Français Pendant le transport, une équerre de mon Ender 5 Plus a été cassée. J'ai repris les dimensions. J'espère que cela vous servira. English During transport a bracket of my Ender 5 Plus was broken. I resumed the dimensions. ...I hope it will serve...

... ... J'ai repris les dimensions. J'espère que cela vous servira. ___________________________________________________________ English During transport a bracket of my Ender 5 Plus was broken. I resumed the dimensions. I hope it will serve you. ...

Ender 5 Plus tool holder. With bonus USB stick holder. The hole for the scraper may be a bit small. ...I modified the file from a CR10 version and don't have the actual scraper from an Ender 5.

Remastered it sometime back to suit the iPhone 7 Plus along with a protective Caseology case.

This is a revamped version of the Mickey phone case for the iPhone 7 plus and 8 plus. No criticism intended towards the original designer, but the file was a complete mess to try and print. I loaded it into Meshmixer and did some extensive repair,...

I didn't create this from scratch. ...The original work was done by dinesh612. They put in all the effort. My contribution was adding the Crealty Dragon and the Ender 5 Plus content to it.

A simple block riser I put together to handle adding on NEMA Z Dampers to my Ender 5 Plus. ... This doesn't change the supported Z print area as it doesn't change the coupler configuration.

This is an adaptable upgrade for the Ender 5 Plus featuring directional guidance to fine-tune your print bed, which can also be compatible with the CR-10S Pro.

This is my design (still in develop) of my TwoTrees Sepphire plus (SP-5).If you have any suggestion please write them in the comments! ...If you like the design and find it useful, leave a like!

Ender 5 Plus Filament Roller ====================== Simple "plug-on" Spool Holder with two 608zz (8mm x 22mm x 7mm) ball-bearings. ... It supports spools with a inner diameter of at least 72mm and a width of max 72mm.

Screen cover for ender 5 plus. Fits perfectly right in the ridge around the screen. ...I would print in black to completely block out the light but white filament makes for a cool effect.

This is a remix of the original mounting plate. ... This was changed to both give a better wire strain relief post and to allow it to mount on the Ender 5 plus carriage plate without hitting the left belt tab.

This is a remix of https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus. I added a taller wire strain relief and adjusted it to better fit around the belt protrusions. I have printed it and it is...

Designed this to keep the wires on the ender 5 plus nice and neat. This is not a flimsy design, they are strong and keep wires well. The pieces attach to the extrusion with a couple screws and t nuts. They are the width of the extrusion so they...

Structure Sensor Tripod Mount http://www.thingiverse.com/thing:856239 iPhone 5,6 Structure Sensor Grip http://www.thingiverse.com/thing:958897 iPhone 7 Plus Case http://www.thingiverse.com/thing:1942852 Print with a Ninja flex or other flexible...

This adapter makes it possible to fit a SKR 1.4 board into an Ender 5 plus without cutting a hole in the case. ... Hardware required: 4 x 3mm screws When its printed, you take a 2,5 mm drillbit and drill the 4 four holes for the SKR board and the screw...

Tutorial 5 ExercisesDesde 5-6a hasta 5-7

BUT you will need one "cable chain dual male end" to attach the Y AXIS REAR DRAG CHAIN BRKT to the rest of the chain > Some glue is required, Gorilla Super Glue Jell worked well for me > You will need "Ender_5_Plus_-_Bed_Strain_Releif_Bracket_Arm2"...

Hence, I removed a section from the side plate's model so that I could manually cut an acrylic sheet and fill in the section of the side plate.A shout-out to the author @jispal01_273738 of the original model for a pretty and functional case for the...

Originally it was remixed by https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus this specific is remixed from remix created by PUCK81...

Filament guide for my Ender 5 plus, have my spool mounted on the side but the filament was making a 45 degree angle into the filament sensor. Not good. Made this to make sure filament enters at a more perpendicular angle. Mounts on stock Ender 5...

The workbench I wanted to set my ender 5 plus up on was a bit smaller front to back than the footprint of the printer, so I made this doohickey. Just shove it under the feet along the edge of the surface it should accommodate the overhang. ... Use...

Ender 5 Plus filament guide enables effortless spool movement outside the printer for enhanced accessibility. A secure attachment is ensured by zip-ties tied through a sturdy tube. ... Print time on standard settings typically ranges from two and a...

This holder consolidates all of the hex keys, wrenches, and the screw driver that comes with the Ender 5 Plus. It also has an extra slot to keep a razor blade in. ...The lid may be a tad loose depending on your printer, so you can add some tape to add...

This is a remix for an Ender 5 Plus - will require 2 of these pointing at the printed object. ... Will be printing in the next day or two to test - any issues I will update this Printing on my E5+ using PETG as that is what I currently have it set...

a simple low profile cable clip of the ender 5 plus hot end cable aka 1/2" split loom. ... for assembly: (2) M5x10 screws (2) M5 T nuts (1) 8" cable tie Second version to re-use shorter screws Tip: Add a second clip for added support

I relocated the electronics enclosure on my ender 5 plus to sit outside my enclosure. There is a small fan on the bottom of the box that is designed to cool the electronics components inside, so these feet lift the box off the table slightly...

... addition to mount LED strips facing to the print. ...Fits nice on my Ender 5 Plus. ...Maybe also on other Printers Before printing, lay it on the back in your slicing software to avoid support-printing Printing: Infill 10% Speed 100%