5 plus 7 3d models

hello this is my modded led light bar holder for my ender 5 plus but will fit others on the main bracket i used 50% infill and on the led holder i used 100% infill this is to fit the led which was from amazon this is the link...

I wanted to mount a Voron M4 Extruder to my Ender 5 Plus while retaining the stock filament runout detector so I designed this piece to mount it much like the stock extruder. ... You will need 4 M3 screws and nuts to mount the runout sensor, 3 M5...

I had been using Satsana Ender 3 Fan Duct - BLtouch for my Ender 5 Plus as they share the same stock back plate. As most the Ender series printers do. Upgraded to the Microswiss Direct Drive and all metal hot end. ...and needed the part cooling...

I wanted a sleek light bar for my Ender 5 Plus, but every standard LED strip didn't fit, so I grabbed xqqqqme's clips and gave them a makeover to match LilTrublMakr's bar perfectly. I removed the v-slot modification and here's what I came up with -...

Remix of Giuliano Moschini's fanshroud assembly for the MicroSwiss Direct Drive for the Ender 5 Plus. I trimmed it down if someone wants just a strain relief. I added channels for 2.5mm smaller zip ties. I printed this on my CR-20 Pro with a .2mm...

quick and easy guide for the ender 5 plus hotend loom. Needs 2x 3mm T-nuts to mount to the back rail. I used PETG but I'm sure PLA would be fine. Just make sure the hole is smoothed out (some nibs from z-seam might want rubbing down) so the harness...

Hello all out there, Here is a big decorative cornet bracket for ender 5 plus printer (or other large printer) I don't know if its useful, but it fill the empty side of the printer. Size 200*200 mm with 50mm clearance. This thing could be used...

This is actually inspired by WyvernPL's fan duct for the Ender 5 Plus. I aditonally made a adapter part to replace the PSU fan with and put the fan grill inside the housing so it is completely flat on the ouside. The tube is raised at the larger end...

This is my first post on Thingiverse, I wanted to add more color to my Ender 5 Plus so I re-created the corner brackets to be printed in any color you wanted. I did a 20% infill, Layer Height of 0.2, wall thickness of 0.8 and did use supports for...

I recently purchased a new extruder gear for my Ender 5 Plus. It's a knock off Bondtech Geared extruder, but works well. However the new gears put the filament path about 9mm higher than stock. I designed a simple spacer to accommodate the increased...

I designed a low friction spool holder to fit the Ender 5 Plus bracket, and it turned out to be too slick. The spool would spin freely on its own without any assistance. To correct this issue, I inserted some packing foam between the spacer and the...

ebder 5 plus microswiss mount setup. 3 screws mounting. you need 2xm4x60 2m20x4 and one screw and nut from an original roller wheel. this braket is used to be mounted under the cariage. each exoslide on the y axe must be mounted as shown...

... stop. ...I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all with machined aluminum and the printer is now very rigid. ...I made a remix of the ender 3 bracket for the limit stop.

EN: I have developed a dual nozzle conversion for the Ender 5 Plus or for all printers with the usual roller guide system. The original mounting plate was modified and re-milled from aluminum. I tested it with a PETG prototype before milling, and it...

I wanted to mount a second one of these cheap hygrometer/thermometer on the back of my ender 5 plus enclosure. I had extras anyway. This version mounts on the back corner of the extrusion and leaves plenty room in the back for air circulation. I...

This is a remix from an Ender 5 plus Z sync indicator by bamcdo. It's minimal design. You need to mirror to fit the other side. You need to use the original pointing model from JonathanA66. The original models did not fit to me, because both they...

This is a magnetic snap-on case for the BTT TFT24 display to attach to a Ender-5 Plus printer equipped with a BTT SKR v1.3 or v1.4 board. Four magnets are holding the case onto the existing LCD cutout. Magnets: 4 pcs 10mm diameter and 2mm...

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

Precision Leveling System for Ender 5 Plus. Using the standard M4 screw, this Leveling System allows z-adjustment of 0,05mm per step. This version is desined to fit a ISO nut M4. If there is intrest, i will upload the adjusting wheel with the hole...

I made a housing to fit the BTT mixing 2in1out extruder that can be mounted on the Ender 5/plus backplate. The hous is made for 2 40x40x10 fans on the extruder cold end an is directing the air up away from the buildplate. I also remixed the layer fan...

Extended Trays for Ender 5 Plus Machines Require Original Parts from Thingiverse Link To build these extended trays, you'll still need to obtain original parts from the following link: https://www.thingiverse.com/thing:4116655. Key Changes to Note:...

This is my version of LED strip support for ENDER 5 PLUS. Is to be print with support , back on print plate. there is a left, and right part, but they are quiet similar, so maybe no matter if you print only one piece twice. You will need : 16...

Update 8/9/2020 ----------------- The original case bottom design has been renamed "Ender 5 Plus Case Bottom - Creality Mosfet" to indicate it's designed for mounting a Creality Mosfet board. A new version of the case bottom and top have been...

Key Features: * Complete protection from dust, dirt, and other debris * Simple snap-on design for easy installation * Reduces noise levels emitted by the printer * Durable 3D printed construction * Perfect for Ender-5 Plus owners who want to get the...

You may locate the crossbar at any height you find suitable for your setup.Also consider printing the End Covers that protects you from the sharp edges that get exposed when you relocate the crossbar:...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. At...

The electronics changes include: TH3D Parts: * EZboard Lite: https://www.th3dstudio.com/product/ezboard-lite/ * Dual Z Stepper Motor Adapter with Cable: https://www.th3dstudio.com/product/dual-z-stepper-motor-adapter-w-cable/ * Heated Bed MOSFET:...

This spacer is specifically designed for users who have installed the BondTech BMG extruder on their Creality Ender 5 plus and still want to utilize the filament run-out sensor. *Update* I initially provided an incorrect spacer, which I promptly...

Bought a 5 plus and wanted to add similar protection to the BL touch. Quickly discovered that I needed to add a few mm to it in order to maintain the clearance of the rail wheel. you'll need a rail T and a 3mm screw that's around 3-4mm long... ...

There are not a lot of options for the LGX shortcut and the ender 5 Plus. I really like this mount for my Ender 3 V2. Its very solid and works well so wanted to mount it to my Ender 5 Plus. I tried making my existing ender 3 mount work by cutting...