5 plus 2 3d models

Also included is an over-the-top tool caddy because the ender 5 plus has a lot of vibration noise when loose things are mounted to the frame (Especially noisy in the Y axis movements!) So this allowed me to remove all tools from the frame and still...

This is actually inspired by WyvernPL's fan duct for the Ender 5 Plus. I aditonally made a adapter part to replace the PSU fan with and put the fan grill inside the housing so it is completely flat on the ouside. The tube is raised at the larger end...

Precision Leveling System for Ender 5 Plus. Using the standard M4 screw, this Leveling System allows z-adjustment of 0,05mm per step. This version is desined to fit a ISO nut M4. If there is intrest, i will upload the adjusting wheel with the hole...

I recently purchased a new extruder gear for my Ender 5 Plus. It's a knock off Bondtech Geared extruder, but works well. However the new gears put the filament path about 9mm higher than stock. I designed a simple spacer to accommodate the increased...

ebder 5 plus microswiss mount setup. 3 screws mounting. you need 2xm4x60 2m20x4 and one screw and nut from an original roller wheel. this braket is used to be mounted under the cariage. each exoslide on the y axe must be mounted as shown...

... stop. ...I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all with machined aluminum and the printer is now very rigid. ...I made a remix of the ender 3 bracket for the limit stop.

I designed a low friction spool holder to fit the Ender 5 Plus bracket, and it turned out to be too slick. The spool would spin freely on its own without any assistance. To correct this issue, I inserted some packing foam between the spacer and the...

Extended Trays for Ender 5 Plus Machines Require Original Parts from Thingiverse Link To build these extended trays, you'll still need to obtain original parts from the following link: https://www.thingiverse.com/thing:4116655. Key Changes to Note:...

This is my version of LED strip support for ENDER 5 PLUS. Is to be print with support , back on print plate. there is a left, and right part, but they are quiet similar, so maybe no matter if you print only one piece twice. You will need : 16...

Since I'm not using the stock Ender 5 plus display, I've remixed a BTT TFT35 mount with a 40mm fan grille. Just an easy no case modification required to add another cooling fan to the case. ...Should fit any 40mm fan, screws for fan mount are M3 length...

quick and easy guide for the ender 5 plus hotend loom. Needs 2x 3mm T-nuts to mount to the back rail. I used PETG but I'm sure PLA would be fine. Just make sure the hole is smoothed out (some nibs from z-seam might want rubbing down) so the harness...

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

The official Creality all-metal extruder upgrade (Pictured) sits slightly wider than the standard plastic Ender 5 Plus extruder, causing the filament exiting from the filament runout sensor to misalign with the new metal extruder. I created a...

If you want to protect your Redmi 5 Plus from damage, get a sturdy hinged case made specifically for it. ...This case features cutouts for both the screen and camera lens, allowing you to keep an eye on notifications without having to take it off when...

This is a magnetic snap-on case for the BTT TFT24 display to attach to a Ender-5 Plus printer equipped with a BTT SKR v1.3 or v1.4 board. Four magnets are holding the case onto the existing LCD cutout. Magnets: 4 pcs 10mm diameter and 2mm...

This is a remix from an Ender 5 plus Z sync indicator by bamcdo. It's minimal design. You need to mirror to fit the other side. You need to use the original pointing model from JonathanA66. The original models did not fit to me, because both they...

I wanted a sleek light bar for my Ender 5 Plus, but every standard LED strip didn't fit, so I grabbed xqqqqme's clips and gave them a makeover to match LilTrublMakr's bar perfectly. I removed the v-slot modification and here's what I came up with -...

hello this is my modded led light bar holder for my ender 5 plus but will fit others on the main bracket i used 50% infill and on the led holder i used 100% infill this is to fit the led which was from amazon this is the link...

... this one in PLA+ for testing. Decided to go another route, but if I had kept it I would've reprinted in PETG. Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.

Hello all out there, Here is a big decorative cornet bracket for ender 5 plus printer (or other large printer) I don't know if its useful, but it fill the empty side of the printer. Size 200*200 mm with 50mm clearance. This thing could be used...

I wanted to mount a second one of these cheap hygrometer/thermometer on the back of my ender 5 plus enclosure. I had extras anyway. This version mounts on the back corner of the extrusion and leaves plenty room in the back for air circulation. I...

The way I have my Ender 5 Plus set up, a cable sleeve just dangles loosely and frequently scrapes against the printer's frame. This is the first modification I've made to the printer. I printed the part with 40% infill, 100mm/s speed, .2mm layer...

I had been using Satsana Ender 3 Fan Duct - BLtouch for my Ender 5 Plus as they share the same stock back plate. As most the Ender series printers do. Upgraded to the Microswiss Direct Drive and all metal hot end. ...and needed the part cooling...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. At...

Key Features: * Complete protection from dust, dirt, and other debris * Simple snap-on design for easy installation * Reduces noise levels emitted by the printer * Durable 3D printed construction * Perfect for Ender-5 Plus owners who want to get the...

... has been created using Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=151461. Instructions are as follows: Using the options selected: hex_size is set to 2.5 hole_delta is precisely 0.15 handle_diameter measures exactly 25

... request. ... Instructions Using the following options: tube_diameter_backlash = 15.5 spool_diameter = 52 quality_level = 80 number_of_supports = 1 chamfer_depth_backlash = 2 inner_diameter_backlash = 1 height_tolerance = 15 collar_width_backlash = 3

My Ender 5 Plus has the Micro Swiss NG extruder and hotend so I took the parts from the one this is logged as a remix of and the Kersey Fabrications parts (https://www.thingiverse.com/thing:3646827). The Y rails go on the outside of the...

Here is my own design for a Phaetus Rapido HF, LDO Orbiter V2.0 on an Ender 5 Plus with Linear rail. 2 x 5015 component fans, 4010 or 4020 Hotend fan, BL Touch bracket and cable routing to the top. Put the fusion file in here with it, anyone who...

The electronics changes include: TH3D Parts: * EZboard Lite: https://www.th3dstudio.com/product/ezboard-lite/ * Dual Z Stepper Motor Adapter with Cable: https://www.th3dstudio.com/product/dual-z-stepper-motor-adapter-w-cable/ * Heated Bed MOSFET:...