5 piece puzzle cube by 3d models

They represent the clerance used by the designer. if this is too loose, pick files with negative numbers. If the files are too tight, pick files with possitive numbers. As the connection "part" is rather complex, then numbers cannot be interpreted in...

New (September 2023): For those who don't want to use Fusion360 - there are now .step files for all boxes from 1x1 to 10x10 available.This is a remix of the original bins by Zack Freedman that you can find here:...

The power supply of the fan is carried out by ACDC converter. In addition to the STLs, all the design files are provided, in case you would like to make some modifications or if you have any doubts about the installation. For the assembly, you only...

she was glad to have been hired but complained about not having suitable working conditions or supplies at some of your organizations so I decided to help you guys out 'This Time' by offering some furniture and equipment that will help her be more...

When you are done, all pins should protrude from the cylinder by the same amount as shown in the 9th photo. Lay your thin rubber band into the grooves in the back side of lock3 part (the fixed cylinder) and stuff the remainder of the rubber band...

For kids with ADHD, autism, or those who just learn differently, a spinner can be a discreet, quiet means of staying on task by occupying their hands. Incorporated into an IEP, they can be exceedingly helpful. After designing a couple of...

Test fit the base plates in the bottom of the plugs, trim edges by scraping with a razor knife if necessary. </li> <li>Glue the base plate in the bottom of the plug, with acetone for ABS, or other appropriate cement or glue. </li> <li>Install the...

This mounts a Raspberry Pi 3B on the right side under the bed, which makes cable management a bit cleaner. Print the bottom part and one of the tops depending on whether you need a slot for the camera's ribbon cable or not. Also needed: 1x M4 T-nut...

This curve is considered a form of a catenary curve, and is governed by the following equation: `y = 693.8597 - 68.7672cosh(0.0100333x)` Where Y is height about the ground, and X is distance from the center of the arch. Because SolidWorks does not...

The relay can be controlled by a Raspberry PI or similar micro controller, but can also be triggered manually. The main purpose of this relay is to make the printer safer and WiFi capable via Octoprint. The part upgrades the printer in several ways:...

The hole on my cooler is precisely 9.7 mm in diameter, so this plug should fit perfectly on many coolers made by different manufacturers. However, I've included the design files, so you can adjust them to suit your needs. To ensure a watertight...

I tried a few designs until I settled for the one in the photos, inspired by the DANGER EJECTION SEAT stickers found in aircraft. If you want the decorated version, use the [buckleFemale--decorated.stl](https://www.thingiverse.com/download:6800224)...

But again, the versions I posted on the other link are easier to install, although the covers shown here could be used by gluing or screwing them to the plug sets at the other link. Again, neither of these intake plugs will work for V8 cars. Please...

Printing: Print the holder by itself. It fits on the ender 3 with zero space to spare (in the X direction). In fact the raft lines may even draw over the edge (Cura) if its not centered but since they are not connected it doesn't hurt anything. Its...

https://www.thingiverse.com/thing:4686693Features:manual set the Laser power or use PWM control, check laser temp and off&nbsp;parallel in-out on DS 15 connectors (in from CNC controlboard, out to aux)Input to use only PWM signal from DS15 pins 2...

Premier essai sous Fusion 360 d'un modèle paramétrique, car j'avais besoin d'un bouchon verseur pour un petit flacon. Sous Fusion pour accéder aux paramètres : Dans l'espace DESIGN &gt; MODIFY &gt; fx change parameters Vous accédez alors à un...

I mounted the backing for it on a 150x150 glass plate, centered on the stock plate by a set of TPU bumpers. I'll be posting the upgrade parts for my mini once I'm satisfied with them. I left it in the oven, fluctuating between 95 and 105 C for about...

You may create your own design just by setting some parameters in the OpenScad Customizer. To use the generator, you need to have OpenScad installed onto your computer. The thing comes along with a zip file containing a few 2D SVG sample files that...

Rubber bands can be made by cutting up a road bicycle inner tube. They make extremely strong rubber bands. To get skis for the other side, mirror the main skis in your slicer. A video of the ski teeter function is available at...

It uses the existing hardware with the exception of the 30x30x10 heat block fan is replaced with a 40x40x10 fan.The enhanced layer fan duct results in improved print quality on the low temp extruder.There is much better visibility when printing small...

By integrating it with the front section of the front receiver, I was able to give it a more flattened and, in my opinion, more aggressive look when compared with the original. It also matches the source material a little better this way. 2. In...

All printers tolerances are slightly different in my experienceImprovements/Tweaks I've MadeWider spine, so film is held betterResized the overall reel width so the film holds properlyOpened up the outer-most sprockets/lengths of the reel (they were...

This case is an ode to the GK61, which possesses a couple of features that allow for the implementation of a gasket mount: (1) the plate extends beyond the PCB by about 1mm at the top and the bottom and (2) the openings on the PCB for the side...

As I passed by a bin of discounted junk I saw some electric clock mechanisms that were real cheap and grabbed one figuring that I might make a clock one day.Well, while sitting at my desk and pulling out my iPhone for what seemed like the hundredth...

You can make and use the strap without the coloured inserts or you can change the look of your strap by simply changing the coloured decorative inserts for ones you printed in another colour. The fastening button and decorative inserts are the same...

Bill folding is often a common method used by the visually impaired but it's not without its drawbacks; too many bills can get very thick. Modern bills have embossed printing that act as a tactile guide, but not all bills have this feature. These...

It must be supported by the text you selected though. (e.g. Bangers does not support it)</li><li>The font. Nice is e.g.: "Orbitron", "Bangers" or "Luckiest Guy".</li><li>Each lines font size individually.</li><li>The distance between the...

By designing around these standard wheelbases, there’s no need to make custom links anymore! Same as the cab, 240mm and 250mm+ width (from outside tyre to tyre) is recommended, along with 120mm diameter tyres. Scale diagrams are shown for mock-up...

The south side of the frieze is preserved fragmentarily and the sculptured surface was badly damaged in the tremendous catastrophe suffered by the Parthenon in the explosion of 1687. This is why the sequence from block XX on is uncertain, but Carrey...

This project is limited only by the visual range where many PIR and Ultrasonic sensors have a limited range. This works great for projects where you want to detect a cold object (not a living body) or objects far away. The base code uses a 10...