5 axis vise 3d models

The user installs the X-axis end stop in its designated position so that it strikes the metal framework rather than the wheel. ...This modification can also be paired with a custom switch cover for added convenience; take a look at it in action.

Here is the rewritten text. ... Setting Y-axis belt tension by mixing it up a notch. ...Printing Settings Getting Down to Basics Rafts I'm Going with None Supports No-Go Resolution Cranked Up to 0.2 Infill 20 Percent Density Level

An improvement to the stock idler. ...The stock idlers on the Y axis are kind of a pain to adjust or disassemble. I designed these to mount on the 2020 extrusion right over the stock mounting point.. ...It's a simple, self-registering design.

Using the following options: Height is set to 30 Nut diameter is 6.25 Diameter of top is 9 Articulation thickness is 1.5 Pressure point thickness is 4.5 Outer diameter is 20 Bolt diameter is 3 Washer diameter is 5.5 Opening width is set to 2 Diameter...

I was not happy with my Z axis end stop, it flapped in the wind and had a small crack form. This end stop snaps very firmly onto the 8mm rod, requiring no machine screws to secure it in place - although I did design holes and nut cutouts for added...

Because of the way I have my spool holder mounted the X-axis cable was getting caught on the filament spool, it was also getting a bit too close to the hotbed on larger prints, so I needed something to keep the cable in the middle. I couldn't...

this is, a Support bearing holder, for a axial thrust bearing, to hold the Weght of Z axis, so the Z Stepper becomes fully weight releaved, (Z-Assembly weights about 2kg) so the Z Stepper, doesn't carry the full weigt anymore. Dont print it if you...

This design is specifically for a Support Bearing Holder to hold the weight of the Z-axis, freeing up the Z Stepper from carrying its full load. The Z-Assembly weighs approximately 2kg. If you don't have an axial thrust bearing like this one, please...

This is a Coupler for the Z-Axis of a 3D Printer, or a Conversion from a 5mm Rod to a 10mm Rod. I printed it with PLA at a layer thickness of 0.2mm: * The printing temperature was set at 205°C. * The heatbed temperature was maintained at 50°C. * A...

I've adapted the style of belt tensioners on my Y-axis by shortening the inner arms, allowing them to press firmly against the front horizontal extrusion. Having successfully implemented this modification, I was pleased with the outcome. However,...

Self-Aligning Z Coupling. ...5 Millimeter Motor Shaft Diameter, Eight-Millimeter Screw Mounting Hole.

http://www.thingiverse.com/apps/customizer/run?thing_id=299663 Instructions Using the following options: articulation_thickness = 2 height = 30 bolt_diameter = 3 nut_diameter = 6.25 washer_diameter = 5.5 pressure_point_thickness = 5 opening_width = 2...

Hello, this is a holder for MGN12h for ender 5 with M4x4 thread

To create a cover for the Left Hand Side Rollers on the X Axis, I had to experiment with Fusion 360 until I achieved a perfect fit. After several attempts at printing the design, everything fell into place and it looked just right. This new cover...

Adapter to install a thrust ball bearing over the Z axis step motor and finally relief the bed weight from its radial ball bearings. - Must replace the four original screws by four M3x10mm. - Recommended to glue the spacer under the adapter...

* In case of a printed model with support: + Remove support material from the areas that will interface with the X-axis mount and where the dial sits flush with the print bed (2 locations). + See the print bed's bottom surface for these areas. ...*...

Chain mount for ender 5 cable management. You can use these clips for the cable guides or just use zip ties. ... https://www.thingiverse.com/thing:4936515

This marks the completion of our third year project, which has taken shape as a cutting-edge robotic arm boasting an impressive 5 Degrees Of Freedom (DOF).

EN: This clip prevents the print bed from moving down (by its own weight) when the motors are switched off after the printing process (Z axis). The clips are easy to put on and allow a movement in Z-direction if the part to be printed is very high...

This is a set of bearing covers to fit the Ender 5 and Ender 5 Pro printers. ...I designed this to fit with the Crossbar relocation models I'm using and I needed a way to keep my fingers from being pinched or my beard getting caught in the belt as I was...

Front belt cover for Ender 5 with relocatet crossbar. Just mirror for other side. Mounts with bolt from cornerbracket. ... The relocators are disigned by [Glitzville] (https://www.thingiverse.com/glitzville/designs) and work really good

This is just a Supportbering holder for 22x8x7 Bearings, to releave force on Y Stepper of Creality Ender 5. ... there is no need for this, it's just a fisrt try in Fusion 360

... to see it in action! The robot features 3 axial and 5 axial versions, made possible by stepper motors, HIWIN rails, and ball screws for lightning speed. ...A STM Italy worm gearbox powers the rotary module with reliable performance.

The new shaft drive perfectly aligns and supports the Y axis shaft. This critical alignment ensures that every step of the assembly process is precise and secure. By incorporating this feature, you can confidently verify that the system is properly...

This is a custom Remix designed for the Ender 5 X-Belt Tensioner, making it compatible with all parts that come straight out of the box. I've also included the original files for the Knob and Screw. ...You can use these exact files to ensure you're...

This is a prototype holder designed specifically for supporting 22x8x7 bearings, which help alleviate stress on the Y Stepper motor of the Creality Ender 5. ... There's actually no need for this particular design as it was initially created with a...

Print in ABS with high infill. ...PETG or CF PLA will probably work as well. Sizes of components and spacers are important. Order of stacking is shown in one of the jpg's. Uses heatset inserts M3 x 5 (d) x 4 4x M3x22 4x M3x30

Натяжитель ремня оси X для Flyingbear Ghost 5. Для Y - https://www.thingiverse.com/thing:5108776. Позволяет откручивать голову не снимая сам натяжитель. Позволяет открутить натяжитель от каретки не меняя натяжение ремня. Плюс позволяет не...

•washer_diameter: Take Care Of Safety With A Thin, Sleek Disc Featuring Washer diameter precisely in Size, Set it Secure with Diameter at an Impressive Measure - 5.5 mm. ...•pressure_point_thickness: Bring Balance And Support Through The Durable...