4x5 viewfinder 3d models
1083 3d models found related to 4x5 viewfinder.
thingiverse
I swapped out a lens board from my b2vn rig to accommodate a custom-sized aperture opening.
thingiverse
I lost the eyecup thing on my A65 camera so I made this one, it was faster than ordering one from aliexpress. ... AFAIK it's the same piece for the the rest of the SLT line but I can't try, please tell me if it fit well on the other models include...
thingiverse
This is a shade for a 1929 model Voigtlander Bessa. It's made to be locked in the film spools holders with the camera open, then helping to make shade for a piece of paper or unpolished glass, helping to visualize the created projection. It can be...
cults3d
This is a shade for a 1929 model Voigtlander Bessa. It's made to be locked in the film spools holders with the camera open, then helping to make shade for a piece of paper or unpolished glass, helping to visualize the created projection. It can be...
thingiverse
Print with tree supports. ...Remove and sand edges where gopro goes.Use 7x eye loupe from Harbor Freight that comes in a set of 5.Super glue eye loupe in and record.More information about recording in txt file.
thingiverse
Comes in two versions. The first version is a basic flat lens board with all parts of the board beefed up for added strength. You can add a custom sized lens hole and if necessary a thinner area for a retaining ring or a thicker area for press...
thingiverse
The adapter works perfectly, fitting smoothly into the JTZ DP30 matte box and holding a 100x100mm filter tray with ease. ...Its compact design makes it easy to use and transport.
thingiverse
based on the FotodioX Pro Canon EOS Large Format 4 x 5 Adapter
prusaprinters
<p>Update 5-Jul-2021: Added a mid section to the 45 version as sometimes under heavy agitation the film edges will poke out the sides.</p><p>----------</p><p><i>Not blocking commercial on this one, and included the Fusion and Step files for you to...
prusaprinters
This is a mount to allow you to atatch a Sony DXF-50 or other similar vintage broadcast camera to anywhere you wish. I chose to mount my DXF-50 to my workbench. Keep in mind that you can power these with an Averkey VGA-to-NTSC converter, and cheap...
thingiverse
Betty Edwards' book *Drawing on the Right Side of the Brain* recommends constructing two viewfinders from cardboard. I decided to make two basic viewfinders for printing. All ratios should be 8:10. They are both 160mm x 200mm on the outside, the...
thingiverse
The fit is secure and tight, the entire frame is visible and sharp, you get accurate TTL metering (including spot) depending on the type of prism used, and the image is significantly brighter and larger than with Mamiya's own porro-viewfinder. So...
cults3d
Keychain with photo. ... Pictures dimentions: 4x5 cm, (40mm x 50mm).
grabcad
Measured from an original LomoGraflok 4x5 Instant back
myminifactory
Hard bed cover for Axial SCX24 Chevrolet C10. ...Mounts from underside of the bedrails using (4) M1.4x5 screws and (2) M1.4x5 screws for the panel.
myminifactory
Single panel hard cover for the Axial SCX24 Jeep Gladiator. ...mounts using stock hardware or M1.4x5 screws and (2) M1.4x5 screws for the panel.
prusaprinters
I started converting some Wide300 cameras to make automatic backs for my 4x5 Super D SLR, but I stopped once the LomoGraflok was announced.Here's my December revision of the riser shim and viewfinder mask. The design uses heat-set inserts...