4x5 tintype holder 3d models

If you're looking to shoot a wide angle lens on your Toyo View 4x5, this board is essential. The central hole accommodates a Copal 0 shutter. Tapered edges at the top ensure easy installation into the camera body. For optimal results, print with high...

This is a 4x5 single sheet daylight developing tank requiring 150ml of developer. Simply load the sheet into the dark bag and develop it under natural daylight with ease. ...For fixing and washing, use a small tray, allowing you to observe the process...

4x5 revised paint rack for The Army Painter Dungeons & Dragons line of 12 ml bottles. Based on the design by bbzed. Front and Back Standalones fully seat in the frames, while the Modular sit half-embedded. Frame Left and Right are...

A nifty Epson scanner enables the scanning of 135 negatives, 120 negatives, and slides, but struggles with 4X5 negatives made with sheet film from my PINH5AD Pinhole camera. The expensive solution is a $600+ Epson V700 scanner; however, the cheap...

... https://www.printables.com/model/219479-lomograflok-4x5-instant-back-with-step-and-f3d-filI also modified scale to be 1:1, so no downscaling is required.What you need:2x Locking Plates1x Graflok BackHardware:4x M4x16 Bolts4x M4 washers4x M4 Nuts

Screen protector for a MK3 Intrepid 4x5 back that doubles as a focusing hood. Should fit the MK1, MK2 & MK4 backs without any modifications. Uses 8 threaded M3 inserts, the baseplate has two holes 40mm apart both on the top and the bottom that...

I'm able to scan only half of my 4x5 film with my CanoScan 9000F. To get around this limitation, I'll simply scan two halves separately and then combine them afterwards. This frame is designed specifically for placing the film perfectly each time...

This spacer fits a Crown Graphic 4x5 camera, and lets you use the rangefinder and viewfinder with a Lomography Instax back. The spacer moves the lens back from your normal infinity setting to match the Instax film plane. The viewfinder mask...

This is a magnifying focusing hood for Intrepid 4x5 cameras. It snaps onto the ground glass back at the top and bottom using clips that can be replaced as they wear or if you break them. The lens used is a 150mm plano-convex lens, which should...

This is an alternative to the ground glass protector that comes standard with the Intrepid 4x5. There are ground glass protectors available for purchase, and they may be a better choice depending on what types of things you're anticipating may hit...

4x5 revised paint rack for The Army Painter Dungeons & Dragons line of 12 ml bottles. Based on the design by bbzed. Front and Back Standalones fully seat in the frames, while the Modular sit half-embedded. Frame Left and Right are interchangeable...

This is 9x12 mask for 4x5 dry rack created by Roland Deegest: https://www.thingiverse.com/thing:2423724. Print Settings Printer Brand: MK3 Printer: Prusa i3 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 10% Filament: Clas Ohlsson PLA...

Plastic parts for the 4x5 QMK Macropad Project.You can check the video from the link below:https://youtu.be/BcXycScePHMShopping list:Arduino Pro Micro USB C: https://s.click.aliexpress.com/e/_Dehy8krMicroswitch Used for Reset:...

This is 4x5 single sheet daylight developing tank. it requires 150ml of developer. You can easily load sheet in the dark bag and develop it at the daylight. For fixing and washing i recommend to use a small tray, its amazing to watch the fixing...

This is a "dark box" designed specifically to store exposed 4x5'' film sheets safely. The box itself is lightproof, making it an ideal solution for keeping your sensitive films protected. However, as an added precaution, consider placing the exposed...

The 6x9 frame is centered both vertically and horizontally within the 4x5 camera's rear standard. Note that because the frame counter shows the 645 frames (not the 6x9 frames), you'll want to expose on frames 1, 3, 5, 7, 9, 11, 13, and 15 to avoid...

This is a ground glass shim for 4x5 Graflex SLR cameras with a lomograflok back. To assemble this shim and adjust it to your specific camera, you will need four m3x16 screws, two m3x12 screws, and six m3 nuts in addition to the printed parts. Your...

This is a ground glass shim for 4x5 Graflex SLR cameras with a lomograflok back. To assemble this shim and adjust it to your specific camera, you will need four m3x16 screws, two m3x12 screws, and six m3 nuts in addition to the printed...

To operate this setup, a ground glass holder from a Graflex camera is necessary. The frame to hold the ground glass can be adjusted using spacers, ensuring optimal focussing. ...Cutting paper to size would work as a shim; photocopier paper, at 0.1mm...

Kodak 4x5 film tank cap with pour spout. ...

- **1x Cassette holder** (2.5cm deep with internal cone to expose the wider 4x5 inch film - This will move the infinity focus point of your camera, so you'll need to compensate for it on the focusing scale - I printed a new one for when I use the...

Filter Adapter 4x4 to 4x5.65 for Matebox Tilta MB-T15.

After wasting so many 4x5 film sheets from missing critical focus, I decided to work with a friend of mind in a 3D Facebook group to design this focusing hood and it has worked wonders. It allows you to focus even hand-held (which I do not recommend...

This lens board accommodates a Graphex 135mm f/4.7 lens, designed specifically to complement the 4x5 Intrepid Camera.

The person is a human being.

Customized version of https://www.thingiverse.com/thing:208591 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=208591

Remixed from CameraObscura to fit glass dry plates better. fits 8 plates.Longer slides on the sides to get the plates in easier, also added a brim on the base so that it can sit on its side level with the lid on. ...Also modified a second lid to use as...

No description is provided for this entity.

I'm still refining the components and they haven't been fully tested yet. Photography has always been my passion. After earning a minor in photography in college but never using it for anything meaningful, I decided to tackle large format...

This is a remix of the WAGO Power outlet by OV1A. I was drawing it as a very new model in FreeCAD. So I added fastenig tabs. If you insert the WAGO connector you can snap it compleetly and it is very strong fixed. You can sand the fast noses a...