4x5 tintype holder 3d models

**THIS IS A WORK IN PROGRESS AND UNTESTED ATM** 4X5 SHEET FILM HOLDER print amounts: latch- 2 middle- 1 middle TB - 2 TB - 2 darkslide - 2 glue together after printing UPDATE: the darkslide and middle top and bottom parts have been reworked. the...

I prefer this simple 2 sheets holder because of x-ray film stiffness and emulsion fragility.Fits nice to the AP and Paterson 2x135 tanks, also must work with 9x12 and 4x5" sheets both.Use any material that have proper chemical resistance, like, ABS...

Here is a single side of a tintype storage box. You'll need to build or design the rest of the box. ... I use this to store 5x7 tintypes in a small wooden box.

Lens box holder for Graflex Speed Graphic 4X5 camera

0.4-1mm pet

Customized version of https://www.thingiverse.com/thing:3408769 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3408769

It might not be 100% done, but it is a good start.

Customized version of https://www.thingiverse.com/thing:2816500 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2816500

It might not be 100% done, but it is a good start.

I made this single sided for 3d printing. I have printed it and seems ok, but not tested it. I just share it here, so others could try it. ...Please comment if you got it working.

I crafted this lens plate specifically for fearless photographers who shoot with their trusty 4x5 and the versatile Skink Pinhole DIY holder. ...Built from sturdy PLA, this plate demands a coat of paint to ensure a light-tight seal, a requirement I had...

This film holder is smaller than a standard 4x5 film holder, and is designed specifically for the Polaroid 4x5 back. Tested for light tightness with ISO 6 litho and paper negatives. Print 2 side rails, 2 pressure plates, 2 hooks, and 1 of everything...

This is a spacer adapter to develop 70mm x 5" film strips to fit on the Stearman Press SP-445 4x5 holder for development. It may splay out a little bit, but should hold the film strip securely. ...If not, then sand the inner surfaces until it's...

One of the missing parts was it's spring back film holder including the ground glass holder. Because I had another 4x5 Speed Graphic, I had a frame to use as an example to design a copy. Some of the details were a bit intricate, so it was a challenge...

This large format pinhole camera works with a 4X5 sheet film holder, replaced by my custom frame for visualizing the inverted and rotated image through the pinhole. A hood or drape is needed to block ambient light due to the faint image produced by...

... ----- Shoot Fujifilm Instax Wide instant film in your 4x5 large format film camera. Printable Insert for 4x5 film holder to position Fujifilm Instax Wide (instant) film. Insert is asymmetrical to center the image area of Instax wide. ...

If you are using the focus screen holder *WillTravel4x5-GLASSGroundglass_topbungee_v4* for your camera you can use these holders to hold the glass in place and at the same time attach a format mask to the screen. Great if you for example have a 120...

Very simple mod to the lid component of Robert Bieber's 4x5 Wet Plate Holder. Basically it's a 0.4mm slit in which you can squeeze in a 0.25 mm leaf spring. The width is 1cm but I found that a wide leaf spring at that thickness is too strong, and...

Adapter to load Instax Wide film into a standard 4x5 double dark slide film holder. The easiest way to do this is to skip the DIY and buy a [LomoGraflok](https://shop.lomography.com/en/lomo-graflok-instant-back?country=us). There is [another...

@wiseprints206 11.28.20 Fixed small bug in 4x5 bracket. Edit: Added slots for nickel strip flow and reduced filament usage. It should bridge gaps without supports, given a well-tuned printer. Edit: Included 4x5 clip. Happy building! I wanted to...

Customized version of https://www.thingiverse.com/thing:666162 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=666162

s

Customized version of https://www.thingiverse.com/thing:1091883 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1091883

A personalized rendition of the model located at http://www.thingiverse.com/thing:53561 was crafted using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=53561). ...The customization parameters included square dimensions of...

A tailored version of the Thingiverse model can be found at http://www.thingiverse.com/apps/customizer/run?thing_id=53561. ...Customize your design by choosing these settings: floor style - stone, no west wall, no north wall, 5 squares wide, no south...

4x5 custom keypad solidworks design. Material selected is rubber. ...Dimensions can be edited.

4x5 custom keypad solidworks design. Material selected is rubber. ...Dimensions can be edited.