4x5 film holder 3d models

This is a non-standard 5x7 film holder for a home made camera.

Camera film holder designed to accommodate standard 88 by 62.5 millimeter photographic paper.

A film holder for scanning APS negatives. ... This is a Remix from : https://www.thingiverse.com/thing:4741606

At work, I constantly need to pack large things in stretch film, it’s not convenient to do it with my hands, so I made a convenient film holder. It is printed easily, the pen itself is additionally needed, I made it from a chromium-plated tube with a...

Film holder for 120 square 6x6 film made up of two components that clamp together to hold and guide the film securely. ... To build one, you'll need: - Printed files - Two rubber bands - Four strips of felt or sponge, measuring 70x7mm and 1mm thick,...

For 35mm, diapositives in 40mm standard frames, 120 in 6x6 and 6x9 format, 4x5". Buy a square 20x20mm aluminium profile to mount front and back base. Set distance to fill whole DSLR frame for the lens you have (a macro lens could be required). As...

This is a Cling Film Holder for catering film. I had a problem where the cardboard box just wasn't strong enough, and the teeth broke immediately. The right part has holes, and the left has pins that are offset 0.5mm so there should be a good fit.

This film holder easily holds 4 35mm exposures in place. Just snap it onto the sprockets and tensions keeps it down. Perfect for scanning! ... I printed at .2mm layer height but anything should work really.

This is version 2 of my cling-film wrap holder. It has larger roll diameter, easier loading and 3d printed cutting spikes. ... Non 3D printed parts: 5 Aluminum angle brackets and 8mm threaded rod.

Edit it online https://www.tinkercad.com/things/gmCCgkn28aO This is basic 35mm film memo holder. The two parts have to be glued together. I placed them on a flat surface, film memo viewing hole facing upwards and aligned them, than I turned them...

Film holder specifically designed for use with flatbed scanners, particularly those in the 135 format, offers flexibility for users of Epson V600 models while fitting other similar devices as well. Optimized for strips consisting of six frames each,...

This is a core holder for 16mm film. It is used to adapt the square spindle common to 16mm camera equipment to the cores sometimes supplied with film stock. This is a press-fit design so the dimensions may need to be modified slightly to get the...

... camera shake when the shutter fires. To switch frames, open the holder, slide the film over, and then close it back down. Position the film under the tube for the next shot. ...A true macro lens is essential for achieving the best possible results.

This holder accommodates 110-sized film negatives perfectly. It was specifically designed to fit the standard 35mm template that comes with the Epson V600 film (and negative) scanner. The holder features bands to block out the area between pictures...

Basic design is same as my 120mm film holder, just modified for 35mm. If this is going to be used in a situation where it might get bumped around a bit, I'd suggest rubber bands to help hold the lid on. ... Lid has uploaded upside down, so be sure to...

A linear polarizing film holder, to make it easy to see and change the polarization of light. The film is held between the outer square and the small inner frame, and the big triangle on the outer square acts as a pointer in the direction of...

Cling Film Roll Holder https://www.youtube.com/watch?v=9XPKqOlNDVc Additional Materials: Aluminum Brackets (2cm x 2cm) with a Thickness of 0.8mm M8 Threaded Rod Two Screws and Washers Plastic Toothed Strip from an Aluminum Foil Box Print Settings:...

Here's a little holder for your 110 film cassettes. It keeps the dust and dirt out when you are done shooting the roll. I used a small piece of PLA filament for the hinge pin. You might have to clear the hinge holes with a drill first. The cassette...

Compact Camera Film Case. ...Store up to 35mm film rolls securely. ...Perfect for photographers on-the-go.

Scan your 35mm film at a high resolution to ensure maximum detail is captured and then analyze it carefully to identify any potential issues that may arise during development.

Minimalist 35mm film holder for DSLR-scanning. Top and bottom glued together, "springs" in slots between. Includes low version (tested) and taller version (not tested). Take care when glueing, springs must move freely. I pressed it together...

Testing an improved film carrier. ...It is still a work in progress, the first version doesn't fit well.

Here is a revised version of the text: "Designing a custom rig for flat film holding is underway for DSLR 120 and 35mm scanning applications. Development progress continues. 3D printing in PLA black with .25mm layer thickness has yielded promising...

This film case is designed to fit 4 rolls of 120 format film. The lid stays in place when closed, I designed it to have an interference fit lip. It took a few iterations but I am happy with how it fits now so I am offering it up to all of you. ...

This is an 8x10 film holder designed to specs. Since most printers don't have a print volume of 296mm, I've split the main body in 2 (part 1 and part 2) with an insert in the middle to help make it stronger, and side overlaps to help keep out the...

I've been carrying my Pentax K1000 camera without a film bag, often resorting to stuffing it into my pockets to keep it safe. I designed this solution to simplify the process of changing film quickly. The strap easily passes through and doesn't...

It can easily be customized for various film formats and different print materials. Print Settings Printer Brand: LulzBot Printer: TAZ 6 Rafts: No Supports: No Resolution: With a 0.5mm print head. ... Notes: I printed this using ABS, and the...

Uploaded for a reddit user Measures 35mm between pins Adjust flow rate after each print so you can get it just right so they hold together and keep the film in place Try scanning from both sides to see which one is more clear.

This is a 4 roll case for holding 35mm film canisters. The lid is designed to hold in place when closed but still open with ease. It took me some design iterations to get the interference fit just right for this design but I am very happy with...

Uploaded for a reddit user Measures 35mm between pins Adjust flow rate after each print so you can get it just right so they hold together and keep the film in place Try scanning from both sides to see which one is more clear. Print Settings Printer...