4s lipo batteries 3d models

I'm going to create an extended battery door for the Nerf Barracade, allowing users to add larger batteries like LIPO packs. Check out this photo where I've managed to fit an 8.4v 2s LiPo pack and a LiPo alarm inside. My design is optimized to...

The BeeRotor X200 has two LiPo straps instead of one, but most LiPos are too short and the straps only just catch the end of the battery. I've added two slightly indented sections that allow the straps to grip well. Given the battery hangs under the...

Created in Fusion 360. ...Protector for my little transtec beetle with DJI Air unit. Print instructionsNeeded a protector for FPV landings - cause the batteries get damaged over time, so I designed this in Fusion 360 to protect the lipo at landings.

Created in Fusion 360. Protector for my little transtec beetle with DJI Air unit. Print instructionsNeeded a protector for FPV landings - cause the batteries get damaged over time, so I designed this in Fusion 360 to protect the lipo at landings.

It would be awesome if you could help me grow my page by liking and following me to get the latest updates and new stuff @ https://www.facebook.com/Dreamlife3Designs/ BoltRc Kraken Lipo 3s-4s-6s Mount Plate This bracket is tailored specifically for...

A Protective Sleeve for the AceHe 4s 850mah High-Performance Battery. Crafted Specifically to be Printed with Flexible TPU Material. Print Settings: Printer: Utilizing a Prusa i3 mk2 Printer. Rafts: Not Required. Supports: Not Necessary. Resolution:...

# 1-4s BT2.0 Whoop Lipo Series Charger ### Building and using this can be, quite literally, explosive. Please know what you are doing and test somewhere that wont catch on fire, like a garage or even outside. Please ask someone who knows to take a...

Can hold 6 turnigy 3 cell 30-40C discharge 2200 milliamp 2.2 amp li-po batteries

Just print as is and cut open the side, put the LiPo in and seal it back together with a soldering iron at 250°C. ...You can also water seal it with liquid tape on the opening for the cables.Print in soft TPU to be able to get the LiPo inside.

A Container for 750 ml Lipo Batteries with Cover is Printed using the CTC Printer, which Prints with a Resolution of 0.1 and an Infill Percentage of 20 Percent. ...Rafts and Supports are Not Used in this Print Job.

http://www.thingiverse.com/apps/customizer/run?thing_id=348618 Instructions Using the following options: battery_length = 137 light = 1 battery_height = 40 thick_edge = 1 sunk_screws = 1 cable_tie_hole = 1 wall_height = 2 battery_width = 45 hole = 3...

https://www.thingiverse.com/apps/customizer/run?thing_id=348618 Instructions Using the following options: battery_width = 82 battery_length = 185 cable_tie_hole = 1 hole = 3 hole_distance = 50 hard_case = 1 light = 1 band_hole = 1 battery_height = 44...

http://www.thingiverse.com/apps/customizer/run?thing_id=348618 Instructions Using the following options: hard_case = 0 thick_edge = 0 hole_distance = 53 battery_length = 140 cable_tie_hole = 1 battery_width = 52 battery_height = 48 hole = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=348618 Instructions Using the following options: Battery Height Set to 48 Band Hole Selected, One Holes Wall Thickness Fixed at 3 Lighting Option Disabled Sunk Screws Not Required Battery Length...

... if space permits. Weighing as little as possible, this cradle actually gains reinforcement once a battery is safely housed within its carefully crafted confines, forming a remarkably strong unit without requiring special installation instructions.

Compact USB powerbank giving you 10Ah from two 6060100 LiPo batteries. Uses the ubiquitous (and cheap) H913-A V2.0 circuit board with 1A and 2A outputs No screws needed, the circuit board clips into place and is firmly held, one or two pieces of...

Compact USB powerbank giving you 10Ah from two 6060100 LiPo batteries. Uses the ubiquitous (and cheap) H913-A V2.0 circuit board with 1A and 2A outputs No screws needed, the circuit board clips into place and is firmly held, one or two pieces of...

You will need : - 20,000mAh polymer lipo battery ( or 2x 10,000 batteries) Buy it at : https://www.aliexpress.com/item/4000192654439.html ( 16$ for 1 10,000 mAh battery ) - Lithium Battery Charger Board LED Buy it at :...

Package of rechargeable batteries designed for use in the 1/14 scale Tamiya truck.

... that maximize airflow while minimizing weight and complexity. By optimizing the airflow pathways around the batteries, these designs help to dissipate heat more efficiently, reducing the risk of overheating and subsequent battery damage.

This is a case designed to hold up to ten 1S 3.7V Lipos (including Velcro) as used on the Eachine QX95 micro FPV quad or similar micros. The bottom of the box is divided so you can print one green and the other red, with power chord on the red side...

This is a case with cover to hold up to ten 1S 3.7V Lipos (incl. Velcro) as used on the Eachine QX95 micro FPV quad or similar micros. The bottom of the box is split so you can print one green and the other red, powerchord on the red side means...

Designed this to fit inside my RDQ bag, and also work well on my race day table. ... This fits several of each of the batteries I use on my fleet so I can keep everything organized easily.

This design is specifically tailored for printing with TPU filament to protect 1500 mAh 4s-6s LiPo batteries used in 200..300 mm racer quadcopters. It bears a striking resemblance to many other LiPo guards found on Thingiverse, but its primary focus...

Lipo Battery Turnigy Nano Tech 4S 1.8A Supports Martian II 220

Connecting the XT60 plug is secured by a protective cap, allowing for easy passage through the force of installation while preventing accidental loss. ...The cap creates a sealed connection that shields against water and protects it from propeller...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/gAieQ8fOI8x

The XT60 connector is equipped with a protective cap that ensures a secure fit when connected, thereby preventing it from becoming dislodged. This convenient feature allows users to easily locate the connector even in tight spaces. ...Additionally, the...