4runner cup holder 3d models
400205 3d models found related to 4runner cup holder.
thingiverse
A friend of mine asked me to make him an insert for his cup holders in his 4Runner. He said they were too big to hold his cups securely. ...I printed in them in petg.
thingiverse
I was tired of the cup holder in my 4th gen 4Runner so I took some measurements and estimated the general shape of the cup holder opening. My print ran out of filament at the end but worked as is, so the actual model might be a little tall. ... ...
thingiverse
... to be more compact. The oversized holders that were always a problem are now replaced by regular-sized coffee cups or water bottles that stay securely in place. ...It took me several attempts to get it right since this was my first build project.
thingiverse
5th Gen 4runner cup holder reducer insert to replace the stock one that gets stuck on the bottom of mugs then lost forever. Made from scratch in freecad. The small without handle is perfect for contigo mugs. The large without handle is...
thingiverse
Print upside down for no supports. Holes are different sizes to fit different size drinks. Added version 10000000 with 2 85mm holes for the ungrateful peasants. I haven't printed the new one yet though. ...
thingiverse
Cup Holder Adapter for 3rd Gen Toyota 4Runners. Specifically fits 32oz Hydroflasks. This part prints in two pieces. ...They're meant to fit tightly together.
thingiverse
Cup holder fits inside the rubber cup holder insert for the 4Runner. Best fit for the cup holder near the front. You must have the rubber OEM cup holder insert for this to fit properly. Super Glue the base to the top, off set from the center,...
thingiverse
I designed this cup holder adapter to securely grip a 64oz water bottle. The design is straightforward, yet effective at accommodating various-sized cups. ...To ensure a snug fit, I attached 3M foam tape to the retention arms, preventing them from...
thingiverse
The rear cup holder on my 2000 3rd gen Toyota 4Runner was clearly due for an upgrade. The left arm had given out completely and was now a permanent resident of the great beyond. This isn't a exact replica of the original, but it serves its purpose...
prusaprinters
To be used with factory rubber inserts, the insert for the 12 oz can will work just fine with the 8.4 oz can. ...If you like the better fit and are exclusive to the 8.4 can print the one for 8.4.
thingiverse
The scales have been calibrated to perfection, allowing for effortless ordering from online print shops like Print a Thing.
thingiverse
I was searching for a cellphone holder for my 4Runner, so I ditched the old magnet that stuck to the air vents. The issue was that I couldn't adjust the vent direction and my iPhone would be facing away from me, making it tough to unlock. I whipped...
thingiverse
Working on designing a phone holder for random compartments on a 2020 4runner. ...This design is for a wireless charging puck.
thingiverse
I designed a coin holder for the 5th gen 4Runer pocket left of the 4wd shift. That pocket is pretty useless as-is. It'll hold about $8 in quarters. If you'd like to redesign your own, the dimensions are as follows: 2.5" long, 1.4" deep, 0.574"...
thingiverse
Switch holder for 90-95 4runner and pickup
thingiverse
It is a friction fit for both the USB cable (into this holder) and the holder (into the blank slot on the 4runner). ...Friction fit was used to facilitate removal (use a small bit of E6000 glue on the back of the largest lip if you need a more secure...
thingiverse
Replacement part designed for the notoriously fragile rear armrest drink holder of the 4th generation 4Runner. A helpful YouTube video demonstrates how to successfully remove the armrest, but replacing the part itself is a challenging task that...
thingiverse
This is to hold the USB cable end for the Cartrimhome T10 head unit for Toyota 4runner. It fits into any blank slot in a 5th generation 4runner. It is a friction fit only (both for the USB cable and the fit into the blank slot), so you may have some...
thingiverse
When I accelerated, the phone would tip over towards the cup holder and the charger would come off. When I made right turns, the phone would tip lip left and the charger would come off. Now it stays put (at least during normal driving). I have no...
thingiverse
Cup Holder Compatible with 1997 Toyota 4Runner Models, May Also Fit Other Vehicles
thingiverse
(1) The adapter plate: This fits into the original holder's spot, partially recessed in the pocket for added stability, using the two factory screws for attachment. It also has back pockets for four 1/4-28 nuts. (2) Mount plate: This plate attaches...