4max pro 2 3d models

Anycubic 4Max Pro 2 Klipper LCD Cove Handy if your a Klipper user and no longer use the LCD. ... Snaps in and can be removed easily with a plastic pry tool Use a Sharpie to get the definition on the logo.

This is a tray for the inside of a 4Max Pro 2.0. I stick it on the left side and throw failed prints into it because I'm lazy. Basically, it's a graveyard. The width is short enough so that the bed shouldn't bump into it if it goes down that far.

The 4Max Pro 2.0 has a problem in Z axis. It results in imprecisions during small movements like 0.1 or 0.05. Using a mesh bed levelling or printing at 0.1 or 0.12 is a pain and the results will be like a russian roulette. Sometimes it works,...

One part is based on this https://www.thingiverse.com/thing:5198158 but i found it too much rigid to work properly, and it gives some movement impediment. The 4Max Pro 2.0 has a problem in Z axis. It results in imprecisions during small movements...

Anycubic 4Max PRO 2.0

1kg spool Holder for Anycubic 4max pro 2.0 dont use supports

I contacted anycubic for 4max 2.0 cura profile so they send these files i will share it with you unfortunately still have some stringing with esun pla+

Anycubic 4MAX PRO 2.0 BIQU H2 V2 base Don't forget change cooling fan from 24 to 12V I'm use heater from original head

This is a modified cold print head lid for Anycubic 4Max Pro 2.0. (Thanks to https://www.thingiverse.com/alex_trask and his model https://www.thingiverse.com/thing:4934115 ). ...Updated version with more cooling and better design.

This is stock-like print head lid for Anycubic 4Max Pro 2.0. My old one is broken, and I created a new one! ... Fusion 360 source file included!

A filler strip to prevent the possibility of the ribbon cable getting damaged on the Anycubic 4Max Pro 2.0. ... Mounted mine with a magnet to the rear support, but adhesive would work also.

I was tired of problems with 4max pro 2.0 display (bugs, lack of modern features, weird protocol, no official marlin 2.x support), so i decided to replace it with modified https://github.com/bigtre.../BIGTREETECH-TouchScreenFirmware). The display is...

This a remix of my favourite fan duct design for the 4Max Pro, adapted to fit the 4Max Pro 2. This is not an elegant remix, its very hacky but it works like a charm. It's designed to use the stock hardware. ... Happy Printing

This a remix of my favourite fan duct design for the 4Max Pro, adapted to fit the 4Max Pro 2. This is not an elegant remix, its very hacky but it works like a charm. It's designed to use the stock hardware. ... Happy Printing

Generally successful configurations for the Anycubic 4Max Pro 2.0. Note: I am using the Knotwurst firmware, which is based on Marlin 2.X. ...These configs may not work the same using the original Anycubic firmware based on Marlin 1.9.

This is a modified cold print head lid for Anycubic 4Max Pro 2.0. (Thanks to https://www.thingiverse.com/alex_trask and his model https://www.thingiverse.com/thing:4934115 ). ...Tried to make it colder with more holes and designed it to look good.

I designed this thing to fix my 4Max Pro 2.0 Y-Axis bearing u need to drill 4 new holes and to cut the distance Use 608 Bearings and enjoy the silence! ...:-) I used M4x20 Screws but u can use M3 too

Anycubic_4Max_Pro_2.0_print_head_withBLTouchMount.stl ist komplett in einem Teil (x_offset=-0.5mm y_offset=-51,5mm)PrintHead_4MaxPro_ReadyForBLTouchMount_v2.stl ist vorbereitet für die Montage des separaten BLTouch Mounts (nicht getestet)...

This is a simple open extruder cover to replace the original extruder cover from the Anycubic 4Max Pro 2.0. I had issues with some filaments loosing little chips inside the extruder toothing which I have to clean sometimes. It is annoying to...

this conversion is aimed to reuse as much OEM equipment as possible . it raises everything 6mm to accommodate the longer hot end assembly . I used a genuine E3D V6 direct drive . The aftermarket hot end requires a flat to be ground in it to fit the...

<p>this conversion is aimed to reuse as much OEM equipment as possible . it raises everything 6mm to accommodate the longer hot end assembly . I used a genuine E3D V6 direct drive . The aftermarket hot end requires a flat to be ground in it to fit...

BIQU H2 V2 adapter for Anycubic 4MAX PRO2.0 Don't forget change cooling fan from 24V to 12V I'm use 12V Heater from original head. For cooling I'm use 12V - Dual Ball WINSINN 50mm Fan. ...The original is fine too.

... for the hot end fan port. DO NOT PRINT USING AN FFF PRINTER. Use PrintBreakRepeat's original 2-part plate if you are using an FFF printer. ...If you attempt to print this design via FFF it'll need a lot of support and the quality will suffer.

Same as https://www.thingiverse.com/thing:5213427, just shortened by about 1 and 2 mm at the upper part to get it higher, since it was lower than the nozzletip on my setup. Works with stock printhead with bi-metal heatbreak and V6 heatblock and...

If you attempt to print this design via FFF it'll need a lot of support and the quality will suffer. Print Settings Printer Brand: Formlabs Printer: Formlabs Form 2 Rafts: Yes Supports: Yes Resolution: Variable Infill: 100% Filament: Formlabs...

I haven't tested the model with openings for press fitted nuts !!!_ - If you decide to go for the models without nuts, I strongly advise you to redrill the mounting holes with a 2.5mm, or a 3/32 drill bit, which is slightly smaller than 2.5mm. You...

I modded the original STL (the model itself is not perfect, but works) for a better cooling and to avoid melting and deformation due to high temperature during ABS prints. Use ABS for this, not PLA. ... Category: 3D Printer Parts

<p>this conversion is aimed to reuse as much OEM equipment as possible . it raises everything 6mm to accommodate the longer hot end assembly . I used a genuine E3D V6 direct drive . This allows for use of left hand bmg /titan extruder assemblies</p>...

I modded the original STL (the model itself is not perfect, but works) for a better cooling and to avoid melting and deformation due to high temperature during ABS prints. ... Use ABS for this, not PLA.

This is my 3M Mask Filter enclosure assembly. ... I power it with a 120mm blower fan that is externally powered