49mm dosing funnel 3d models

Rather than using "math" and "measurements" I offset the original funnel in 1 degree increments and hoped for the best. The picture above is 8 degrees which is too much. If I printed again I might go for 6 degrees. ... Try your luck and reply back...

Here is my version of a single dosing hopper for the Baratza Sette 270: I designed it to perfectly complement the grinder's sleek lines and intuitive design. For the lid screw, I opted for an M2 x 20mm screw that provides just the right amount of...

...The funnel was designed with a straight cylinder that's the same width as the inner diameter of the La Pavoni basket after shrinkage (designed at 50mm diameter). The tamper fits into the funnel with limited play and ensures that your tamp is level.

A self leveling tamping station designed for the 49mm basket of a pre-millenium (generation 2) La Pavoni Lever Espresso machine. The basket sits flat in the base and the funnel screws on top. The funnel was designed with a straight cylinder that's...

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

<p>Please print with food safe filament like PETG.</p>

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Please print with food safe filament like PETG. Matching neodym magnets:Shape:discDiameter (D)5mmHeight (H)5mmTolerances+/-0.1 mm           May not fit to all VST-Baskets. Please check the outer diameter, should less or near 70mm. ...(see comments)

<p>Attachment to porta filter is realised with eight 2x4 mm cylinder magnets.&nbsp;</p>

This is very simple design, it works so I might was well upload it. No support needed. ... Pop this on top of your 51mm portafilter basket to make it easier to load coffee.

58mm Dosing Funnel for Breville Barista Max (VCF126X) and Max+ (VCF152X) Espresso Machines. Print upside down without supports. ... Two versions, choose yours: - 0.6 nozzle, 0.4 layer height, 0.6 layer width TESTED - 0.4 nozzle, 0.2 layer height,...

### Features - Contacts the basket exterior, since internal funnels leave a void in the coffee grounds - Friction fit to hold basket in place, since magnets barely stick to 304 Stainless Steel - Funnel doesn't have to be held in place, can be flipped...

made 58mm wide to fit my solis coffee grinder, and extended to catch coffee crappy edit made with tinkercad, but it works

Print comes in the correct printing orientation, prints with no supports and should not require a brim. ...Works very well for my moka pot.

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Tweaked to fit the IMS Basket better.

haven't printed it yet

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

<p>Top fits in Breville / Sage coffee grinders to catch stray grounds otherwise lost during coffee grinding</p><p>Bottom attaches directly to 54mm portafilters and prevents spillage during distribution with a <a...

A simple one-cup brewing container accessory - Gaggia Standard Portafilter Basket and Similar Devices.

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738

Customized version of https://www.thingiverse.com/thing:3144738 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3144738