48v ebike battery 3d models

... charge it (up to 120W). For the parts I used, check https://www.prusaprinters.org/prints/70263-rad-power-ebike-battery-adapter I stopped putting them on Thingiverse after they started mucking with all my links so they could make money off them :-(

The original design was great but I needed something bigger to fit 52 batteries in 13s4p 48V configuration. XT60 connector (controller) DC 2,1/5,5 connector (charger) Relatively tight fit like in the original. You can try to print all parts in...

Wall mount for NCM battery charger - Type: DC483DE 48V 3A - Dimensions:: 5 x 8 x 18 cm

This is a box for a standard 36V, 48V, 17-18A eBike controller. ...Make sure to download the following files as well: * Controller Box Cover Down * Controller Box Cover Top: https://www.thingiverse.com/thing:2730935...

A 48V-Li-battery used in anelectric bicycle.

Holder for Ecotech Battery - 2 Batts for 48v system

eBike Electric battery from a ebike "universal" that I´m mounting on my brother Scott mountain bike. Soon more info on my blog http://thetrxproject.blogspot.com/. ... TheTRXproject Facebook page...

48v MBT4820Li Mountfield lawn mower battery mount can be used either way up to hang the battery on just hold it on a shelf. I did have a hole for the battery to lock in but it made it hard to get out so I removed it. ... I printed it in PLA.

Printed in 2 parts to fit most printers. ...Print 2x 1.stl and 2x 2.stl I will also make a ebike case for this soon

48V 54Ah LiFePo4 Battery PackALUMINUM BOXEASY TO MANUFACTURE

A battery holder for my ebike.

a thing to support ebike battery on round bar

Battery Gauge for Ebikes, I opted for an affordable Chinese Lead-Acid-Lithium-Li-ion-18650 battery gauge: https://www.ebay.co.uk/itm/Lithium-Ion-Battery-Packs-Capacity-Gauge-Meter-Indicator-Digital-Display/283041467382?var=583421126932

I'm trying to find a replacement battery holder for my eBike's HL 48-volt battery. ...The original holder was included in the Bafang ebike kit I purchased, but it has been holding up well despite being designed and printed three years ago.

This Ebike Battery holder only works for batteries with the 3-Notch design.Print Settings:Nozzle: 0.4mmLayer Height: 0.2mmWalls: 3Infill Pattern: GyroidSupport: EnabledFor better results reduce the layer height to 0.12mm.

Shelf to hold my battery on my ebike. uses Velcro straps to keep it in place. ...Also made a tray to keep the battery from sloshing around side to side. Category: Electronics

Shelf to hold my battery on my ebike. uses Velcro straps to keep it in place. ...Also made a tray to keep the battery from sloshing around side to side.

https://ciclotek.com/gb/li-ion-battery-sets-for-ebike/30-bs-36v-128-ah-battery-set.html That battery fits inside. inside was filled with foam sheets to keep battery in place and also work as damper for vibration, and the 2 parts were glued together...

This is a replacement handle for all bosch powertube ebike batteries. Print as sturdy as possibly. ...My settings are:</p><ul><li>infill 30-50%</li><li>3 perimeters</li><li>paint-on supports for notches</li></ul><p>Happy printing</p>

I converted my bike to ebike so I needed to came up with some holder for a battery. It is Hailong battery: https://www.aliexpress.com/item/32914092155.html?spm=a2g0s.9042311.0.0.7bfa4c4dPRZptF I print this in nylon and use M5 40mm screws. PLA is...

e-bike battery case

14s 6p battery box 50% Infill or 100

This calls for an e-bike battery replacement.

Bottom cover for Rattan LM/LW 750 battery. ...Use to cover bontacts while charging your battery or in storage.

I Designed a cover for the battery instead of the one broken off from my bike. ... Hope it fits your battery too :)

I'm charging my Trek Rail 5 battery indoors, and wanted to have proper holder for battery. So.. Just Print it. Attach with screws tp wall, first bottom (handle end) and then use battery as measurement tool to get upper (charger end) to good...

https://www.aliexpress.com/snapshot/0.html?spm=a2g0o.9042647.6.2.74d54c4dRsM81H&orderId=3012757144333620&productId=32796315892 My 10SP5 battery is made using original Liitokala 35E 18650 lithium battery 3500mAh 3.7v 25A...

Components for the missing/broken sections of the battery sleeve. Includes faceplate, bracket, and lock assembly. ...Static study was completed on the bracket to determine width and thickness.Parts were printed using a PrusaMini and are holding up well!

... with the handle end on the bottom. Then, use the battery itself as a guide to position the top (charger end) perfectly. ...There's also an STL file available for mounting the Bosch Compact Charger on the wall, and it requires no supports whatsoever.

My original battery cover was so frayed, that it was nearly impossible to put it back on.So I printed a replacement in PLA, for my surprise it fitted perfectly. ...It's easy to remove and wont get lost while riding.