45mm to feet 3d models

Originally designed to store rolls of rubbish bags inside the cupboard with double-sided tape. But in the end I never printed it. ...Let me know if it's of any use to you :)

I opted for 70mm M3 screws due to their availability, and consequently reduced the length of the 50mm spacer accordingly.

... The parts fit perfectly, perfect for having a solid and larger Discoeasy! ... Tip: For the reinforcement rods, they need to be the same as the DE, because the 3€ steel rods at Leroy's are not straight and you'll have to use a hammer to get them in.

To get the best performance out of this print, you might want to roughen up the middle section for responsiveness. Adding starburst or reducing the gap slightly could also give it a boost. ...Feel free to share your feedback and try out your own...

The PLM-30-CAT6-NAC Pneumatic Light Mast from Larson Electronics offers a secure and efficient method to deploy security cameras and other electrical equipment at heights up to 30 feet. The telescoping, pneumatic light tower mast is designed for...

This door opener allows you to open large doors with a pull handle. ... Both nipples are used for toilet locks, and the longer one for buttons.

this is a plug for the intake after reeds but before carb made to fit 2018 xcw250but probably fits a bunch of bike.

I made this spices holder for my kitchen in order to save space. It's designed to fit Ø45 mm pots. So be sure your spices will fit. Made in PLA, with 0,2mm resoultion and 10 or 20% infill (can't remember). ... I hope it will be useful for you.

Lower the printing speed to between 15-20 and set the temperature at 230°C. Additionally, use a low retraction rate, incorporate support structures, and fill density at 100%. ...In German, this is referred to as "slow printing with minimal retraction."

... from eBay, and this one stands out as the best I've discovered (Liquid filled and 100% Accurate). ...The only issue with it was that it lacked a holder or mount, so I designed an attachment system to secure it to a zipper, backpack, or diving gear.

If you don't want to use drive shaft or for drill, you can use hex nut and M4 screw as length up to your requirement, 50mm / 2" recommended nut outer is 7mm. Making drive shaft 10mm with 12mm thread soon will be available. Tell us if you need any...

The device was specifically engineered to be used within a collection of microphones intended for public address systems, so people can freely obtain it, pass it along, and spread the information far and wide ! ...:)

A custom adapter is required to accommodate a standard headlight on mounts designed specifically for the DAX headlight. ...Unfortunately, I do not possess the standard headlight mount, instead having an aluminum mount of unknown origin.

Here's how to use Thingiverse's online customizer: Select from a range of different designs Customize each option as needed Make sure you know what settings work best in conjunction with the components that have been specified Note: For the robot...

This device allows large door handles with a pull handle to be opened. ...The two buttons are used for toilet locks, and the longer one is used for push-button locks.

A quality vacuum nozzle is designed to pick up dirt, dust, and debris from various surfaces. Users can easily attach and detach these nozzles from their shop vacs, making it a convenient cleaning solution. The durable construction of these nozzles...

The tempera allows you to precisely control the temperature of the water, which helps to achieve the desired taste and aroma of coffee. ...With the help of tempera, you can easily prepare a drink with the right strength, do not digest it and do not get...

My only issue with it was that it lacked a holder or mount, so I designed an attachment that allows it to be securely fastened to a zipper, backpack, or diving gear. ... Check out my other designs at your convenience and follow my regular uploads for...

Support plateau created by Baptiste Gonon-mathieu Modified by Me Knob M3 and Magnet Plateau created by Me Modified plate for those who want to expand their X-axis: https://www.thingiverse.com/thing:2516433 I had more space for the screw, so I made it...

Using the connector, two separate pieces can be permanently combined into larger units (for example, two 15° tracks R1 to form a 30° standard track). The end pieces are half-sleepers that can be stacked together and secured with a clip. ...This makes...

... original R1-LGB-Weiche L12050 (or L12150). However, the straight track is extended by 41mm with the compensation track L10040. The switch mechanism allows the separation of the switch, thus preventing derailments due to incorrect switch position.

You'll find clear directions below for getting started: First, select your preferences: * Fan side length: set to 45 units * Mesh offset: established as 68 units * Clearance of mesh: exactly one unit high * Thickness of the mesh: precisely 1.5 units...

I'm not sure I understand what you're asking me to do. Customized version of http://www.thingiverse.com/thing:28566 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=28566 Instructions Using the following options:...

... bearings, and specially designed wheelsets for completion. A notable enhancement to this design is a 24-inch wheel diameter, resulting in a scale of approximately 1:20.3. ...This oversized wheelset is intended for use on a 3-millimeter axle.

I cut some holes in a built-in closet I made but then realized that cover plates of this size are very difficult to find. The cover plate is friction fit. ...I printed it in PLA and it came out beautifully.&nbsp;</p>

To rectify this, I designed an attachment compatible with zippers, backpacks, and diving gear. Don't forget to explore my other creations and stay tuned for my weekly KooKoo uploads. ...Check out the compass here:...

http://www.thingiverse.com/apps/customizer/run?thing_id=1109083 Instructions Using the following settings: wall_thickness is set to 1.4 units box_height stands at 45 units card_width measures 45 units tolerance is precisely zero units stack_heights...

I needed to shorten one of my Lack tables and rise another. ...Thus, I needed a leg connector to go with the nice feet TheRealMozes designed. ...So I remixed the leg into a connector.</p>

... or another adhesive. ...His feet are now visible due to the removed platform, making him look cute and balanced by his tail. Customize him with a Sharpie or paint. Finish off with a laugh: how does one get Pikachu on a bus? ...The answer is Pokémon!

The Larson Electronics PLM-18-CCTV-NAC Pneumatic Light Mast offers a secure and efficient method for raising lights, security cameras, and other equipment to heights of up to 18 feet. This telescoping pneumatic light tower mast features an...