45 single adapter 3d models

When used with a 50mm lens this allows you to reach 1x - 3x macro magnification (focusing to infinity is impossible).I'm using a Pentax K lens with a metal lens adapter to Canon EF (various other lenses including Nikon can be adapted too).Filament...

When used with a 50mm lens this allows you to go from about 1.2x to 3x macro magnification (focusing to infinity is impossible).I'm using a Pentax K lens with a metal lens adapter to Canon EF (various other lenses including Nikon can be adapted...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: gammaTooth = 2.3125 MusicCylinderName = new song axisSlack = 0.6 midBigTeeth = 21 pulleySlack = 0.45 gear_gap = 1 snapAxisSlack = 0.3...

This cleaning Box will be always printed                                                            ...

it applies to lots of objects like bolt heads, nuts, and threaded rods.Supported...

Original text has been rewritten in 45 words. щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ щ...

The multicolour designs are achieved by simply doing material swaps on a standard single nozzle FDM printer.The box is opened by turning the twist collar to unthread it and open the mechanism. It is further rotated, while holding the base stationary,...

(.125" shank) single flute end mill. As I was running additional tests suddenly the mill would bury itself in the material. The end mill was pulling itself out of the collet. I tried to tighten the the knurled collet with pliers but it still pulled...

(Coming soon) A new smoothed revisitation of the TPB, with optional Crawler Front Bumper, Single Cab, Flat Bed and more! - Tesla Model-S Body. Use the chassis sides provided for KIDS in the Model-S publication instead of the standard ones and set...

For the best looking brick, you'll want the top surface of the brick part of the model to be a single continuous print from one corner to the other instead of going around the areas where the studs will be added in later layers. To accomplish this...

Of course the empty plates could be printed in one color only, but I decided to also print them with color change, so that one can easily make sure to have the textured side on the front.The tags and the trays are printed with 0.2mm layer height in...

While I was redesigning it, I also figured, well, let's build it with a bit more thought into everything that was clunky: I remixed a number of objects, and re-included a few of the parts I'd designed for v1 under this single Thing here, to simplify...

You can use a M3 screw to position and tighten the nut in place.• Install the rail using wood screws, use at least 4 screws on the outer corners to mount the single rail and and 6 to mount the double rail. (extra screw holes are available if you plan...

Leaving spaces unoccupied by the ptfe tube can cause a malfunction in the filament loading.Optional:You will see that the single connector has a cutout that reveals the ptfe tube. This is to use the ptfe tube without using the connector. It has been...

You can use a M3 screw to position and tighten the nut in place.• Install the rail using wood screws, use at least 4 screws on the outer corners to mount the single rail and and 6 to mount the double rail. (extra screw holes are available if you plan...

They make sure that the T-Nuts can rotate freely during installation, your part doesn't slip during installation, and your part doesn't rotate or spin after installation in case you use only a single mounting point.The area around a 3.5mm radius...

### Marking visibility To make the markings more visible one can change to a contrasting filament color for the single layers below the groove bottoms. Ironing the visible portions of those layers is recommended (quick way: enable ironing for all...

In addition, LEDs are also safer for the environment as they are 100% recyclable, which eliminates the need for costly special disposal services required with traditional gas burning and arc type lamps.LED Drivers: Even in LED fixtures, heat is the...

:) There are two variations of the model; one has an additional thin cutting edge that is 1 mm in height and about 0.5 mm in width, so if you have a 0.4 mm nozzle, it will be a single path wide. That's the one shown in the photo. It's probably the...

So print as many of these (front + rear of each) you need for your setup.The cutouts in the panels are also compatible with the airlocks that come with the PolyDryer, two of them are included with a single Polydryer.Assembly GuideFirst of all, use a...

Every single comment, idea and improvement request was evaluated and made it into this version in some shape or form. In a strange way, this is where organic design meets crowd·sourc·ing, resulting in a high performance duct design that has produced...

A set of printed components to build a robot arm that can be controlled and managed by any of the Raspberry Pi single board computers (SBCs),  This robot arm project with Python software and documentation, available from here, developed for the...

 It's best not to mix the two different toe feature types or heels with toes. For example, here is a single temple with heel patterns for a kingpin and shift.  Template_Library.scadUse this file to  make or modify an existing...

All 3 components are soldered together on a single prototyping PCB. To this prototyping PCB is then soldered a 1x8 Pin Header (2.54mm) so that the PCB can be connected to the front pin header of the M5StickC. As power supply off all 3 modules, the...

You will likely have to try several times while tightening the U-bolts or M3 bolts before you attain perfect alignment of the 2 left bushings.// - Do the same wear-in procedure with the single right bearing without mounting to bed (you will align...

:) I included the modified STLs I used to make mine, basically smaller versions of DIY-Machines version and more of them and I added separate diffusers instead of his multi-filament versions, so that they can be printed on my smaller single-color 3D...

The lamp is a "snap/push together" construction. Basically, you need to print a lamp base (two 2-material .3mf, around 10 hours in total), attachment parts (a single material .3mf, around 2.5 hours) and the lamp shade of your choice (two copies of a...

I can provide alternative parts for this if required. Spring: I purchased a 20mm spring initially which was too long and I cut it down, the 10mm I have is slightly too short so would recommend a 15mm or 20mm and cut if required. DockNote:...

You can use a M3 screw to position and tighten the nut in place.• Install the rail using wood screws, use at least 4 screws on the outer corners to mount the single rail and and 6 to mount the double rail. (extra screw holes are available if you plan...

There 3 versions with the latest being the stencil type allowing simple single filament prints where the stencil contrasts through door colour, rather than need a multi colour print and also there is a hole rather than a hook to prevent it slipping...