40w laser cutter kit 3d models

An adapter for the cheap eBay 40 watt laser cutters to let you attach the hose directly to the back of the cutter. ...This allows you to use an in line blower fan, which eliminates positive air pressure in the hose and lowers the chance of fumes leaking...

I've included the original solidworks file if you want to modify it (obviously give credit where it is due if you post somewhere) The hose barb itself fit perfectly with the hose that came with the laser cutter. If you have an imperfect seal between...

This part replaces the small holder for the laser to achieve better stability in the laser

Download to lay down your own Chinese 40W Laser Rule / Registration Mark for easy, visible workpiece alignment.

Fume chimney for the cheap Chinese 40w laser also known as K40 from eBay. made it that way so i can put it as close as possible to the wall because I'm pretty limited in space at home. fits a 120x120mm Server fan and a 100mm vent tube. i will add...

The exhaust fan shipped with this $295 Chinese Laser from EBay just does not seal well, so I created the backplate using the laser cutter itself from an 1/4 plywood piece (ExhaustPanel.svg), with a hole that lines up with the rectangular slot in the...

Fixture to hold a red laser diode at the correct angle to show where the laser will cut. You may need to pass a 6mm drill-bit through the angled hole if it's too tight. Also, tap the hole in the side, 4mm, this is for a set screw.. I found it...

An adapter for the cheap eBay 40 watt laser cutters to let you attach the hose directly to the back of the cutter. This allows you to use an in line blower fan, which eliminates positive air pressure in the hose and lowers the chance of fumes leaking...

The problem with aligning the 40W laser cutter is that the beam is invisible and burning the tape smokes up the mirrors. I made this jig to mount to the end of the laser to align the mirrors with a visible laser beam. Just remember to remove the jig...

-print both laser alignment pieces -attach the laser holders to the alignment pieces with #2 screws (I think I used 1" long, which was a bit longer than needed) -attach the assembly to the laser cutter. I mounted mine to the existing holes from the...

This is a clip to hold the water coolant tubing from a chinese 40w Laser cutter/engraver. Printed in Abs the "spring" effect is perfect. The clip is made for a tube of 9.1mm (about 3/8"). ... Enjoy!

​This is a clip to hold the water coolant tubing from a chinese 40w Laser cutter/engraver. Printed in Abs the "spring" effect is perfect. The clip is made for a tube of 9.1mm (about 3/8"). Enjoy! ...Print Settings Printer: ...

12mm Laserpointer to mount in a K40 Chinese Laser. Use 3mm screws to connect the single parts. ...

... 5v laser diodes. Both of the allign exactly with my laser and when the 2 dots become 1 the item is at the right distance (and the cutting laser is in focus) * The "laser houder" (u need 2) is used from https://www.thingiverse.com/make:301584. ...

... It uses the ventilation supplied with the laser cutter. ...As the ventelationen now fills out the entire exhaust hole of the laser my ventilation has become much better, and therefore I could go 35-40% down in power when I have to cut 3mm wood.

It uses the ventilation supplied with the laser cutter. As the ventelationen now fills out the entire exhaust hole of the laser my ventilation has become much better, and therefore I could go 35-40% down in power when I have to cut 3mm wood. ...Print...

It uses the ventilation supplied with the laser cutter. As the ventelationen now fills out the entire exhaust hole of the laser my ventilation has become much better, and therefore I could go 35-40% down in power when I have to cut 3mm wood. ...Print...

... you have identical components as the original. ...Check out these photos of a build we did at kf-designs.com/2017/06/30/co2-lazer-40w-modification for reference and guidance. ...Also, see our album on Goo.gl/photos/Yg9YypmkULTCeg3ZA for more visuals.

co2 laser cnc

Support for my K40 40 watt laser cutter table. Uses 1/4" hex expanded aluminum as a new stage. Print three of each part. Uses the following hardware 3x 3 inch 1/4-20 brass screws 6x 1/4-20 jam nuts 6x 10-32 x 1.5" socket cap screws 6x 10-32 jam...

Mounting for laser tube 40 watt. Printing with ABS plastic. Profile 30x30. ...Bolts m5 mount on the profile, pipe connection m3.

This 40-watt CO2 laser tube measures 50mm by 700mm and is a generic Chinese product. It matches the precise dimensions of an authentic component I acquired recently. ...The quality has been satisfactory so far, providing efficient performance.

CO2 40W laser tube clamp for Chinese 40W CO2 Laser Engraver/Cutter

CO2 40W laser tube clamp for Chinese 40W CO2 Laser Engraver/Cutter

See:http://www.instructables.com/id/DIY-40W-CNC-Laser-cutter-from-bad-to-better-with-3/ Used: http://www.thingiverse.com/thing:16627 as pulley model. ... Please notify me if i've missed something or you see a flaw.

vent adapter ring for 4" exhaust vent to the 40W co2 laser

Made This Simple Bracket To Mount and get My New 40W Neje Laser Module Closer To the Work Area

Air assist for 40W china laser. ...Friction fit but can use M3 bolt to hold in place Base of nozzle set just above standard focal length.

Used as a window for a cooling tank for a 40 watt laser cutter with a submersible water pump. Holes are for 4-40 screw. I used some 1/2" long flat head sheet metal screws that were lying around and used a counter syncing bit to make it flush. Would...

Bumper guard for the Xtool 40w laser head Mounts on the forward right and left corners to protect laser head from striking the frame rails 1mm thick with clip-on attachment; does not interfere with magnetic plastic vision guard