40mm fan duct 3d models

Adequate clearance has been maintained between the fan duct and hotend heat sink fins to minimize vibration occurrences when they're in close proximity. Notably, the device's center of gravity is strategically positioned seven millimeters below its...

I'm updating the E3DV6 remix of the CR10 mount to work perfectly with the Anet A8.

A cooler is available for 40mm fans with a third air hole. A cooler 2 is available for 60mm fans with a third air hole. ... It's a remake of https://www.thingiverse.com/thing:2748650

A 40mm fan ducted shroud is designed for Prusa Mendel printers, featuring LM8UU linear bearings and J-head extruders. Its internal flap adjusts airflow to the hotend, snapping between LM8UU brackets or secured with double-sided tape. The duct aligns...

This is a remix of my E3D V6 effector for Kossel, with 5015 radial fan duct or 40mm standard fan. Is full compatible with my "ONZProbe" and BLTouch. Created by Diego Pol Bodetto and Marco Robustini. ...If you want to offer me a coffee:...

This is a reworked remix of my E3D V6 effector for Kossel, paired with either a 5015 radial fan duct or a standard 40mm fan.\r\nIt's fully compatible with both my ONZProbe and BLTouch models.\r\nThe creation is the result of collaborative efforts...

I gave the small clamp piece in Marty's direct drive extruder a complete makeover, adding a hinge that makes attaching the fan duct a snap. My own design for the fan duct is far from polished, but it gets the job done just fine. The OpenSCAD...

This is an updated design based on [thing:822476](https://www.thingiverse.com/thing:822476) featuring a 40mm fan in place of the original 50mm fan.\r\n\r\nAlso included is a compact slim version that fits over the X belt, rather than passing through...

Here is my first attempt at designing a compact extrusion fan duct for an E3Dv6 hotend fitted with a K style extruder. As of now, I've left out key components like the motor, E3D heat sink fan, and additional plastic parts of the extruder from the...

Remixed fan duct from @Nicofr57 fits nicely on my official E3Dv6, but the provided hotend clamp is totally wrong (diameter of the hotend too small, wrong distance between screw holes). Unfortunately, I couldn't use the clamp from @AndrewBCN...

I designed a custom duct to fit perfectly around the heat block on my trusty E3D V6 Lite hotend, and now I'm thrilled to share it with you. First, I added a convenient adapter that securely attaches the extruder to the printer's frame. Next, I...

40mm fans mount for DMS DP5. ...The original 30mm fan is laughable.\nI strongly advise using hot-end thermal insulation if you're planning to use very powerful fans.\nTo print this design, you'll need a printer with exceptional bridging...

Introducing the new 40mm fan fan duct version 2 - customize your drilling according to preference! ...Check out the instructions and get creative.

In the process, I also changed the v6 heat sink's 30mm fan to a 40mm fan because the stock one is very loud. The design includes my own layer fan design. The adapter is mounted on the ring that surrounds the heat sink using the same original screws....

The front fan is a 24v 40mmx10mm fan while the top two fans are 12v wired in series, each being 40mm x 10mm fans. If you already have a BLTouch setup installed on your printer, you'll need to adjust the sensing points in the firmware as this mount...

The front fan is a 24v 40mmx 10mm fan and the top two fans are 12v wired in series 40mm x 10mm fans. If you already have a BLTouch setup youll need to adjust the sensing points in the firmware because this will offset the BLTouch more than the normal...

Update: E3D 40mm Fan Duct Update 2019/09/13: - Introducing the Open Version - Featuring a Compact Close Short Version

I've been searching high and low for a way to boost the cooling system on my i3 Rework, and finally found something that really delivers. The original designs were just out of reach, so I decided to tinker with them myself and came up with this...

This triple 40mm fan duct is specifically crafted to fit snugly around E3D V6 style hot-ends. It's engineered to snap securely into place around the V6 heat sink and provides mounting points for a 30mm long M3 screw, nut, and washers to ensure extra...

Fan duct with 40mm fan and large heating block measuring 20x16x12mm, complete with a silicone cover. The top opening has a diameter of 10mm, while the bottom opening measures 22mm in diameter. ...A mold for creating the silicone cover is available on...

I crafted a high-performance fan duct, fitted with two robust 40mm fans, specifically for the Chimera and Cyclops systems. This setup demands an adapter that seamlessly transitions from a 30mm to a 40mm diameter, ensuring a snug fit between the fan...

There are two versions of the fan duct nozzle: the 40mm Fan Duct and the 40mm Front Fan Duct. The former is a large duct that mounts to the extruder in place of the original radial fan (using the same screws). It consists of two pieces: the 'Fan...

A 40mm fan needs a duct that's specifically designed to fit its unique specifications. That's why you'll want to get your hands on a high-quality fan duct made just for this size of fan. ...This type of duct is crafted with precision engineering to...

... cooling fan duct for my DaVinci, and I really liked the design oscahie came up with. ...The only problem was that I had a 40mm fan instead of the 50mm one this design was originally made for, so I took it to Tinkercad and modified it to fit a 40mm fan.

I fabricated a fan adapter so I can utilize my 40mm fan with Thorped's duct. Not an ideal fit, but sufficient enough. Thorped's fan duct: http://www.thingiverse.com/thing:1621937/ The fan plate source code is from...

I made a fan duct so I can use my 40mm fan on Thorped's duct. ...Not a perfect fit, but good enough. Thorped's fan duct: http://www.thingiverse.com/thing:1621937/ Fan plate source code from http://www.thingiverse.com/thing:735038 Please note that the...

This heatsink fan duct utilizes a powerful 40x10 fan specifically designed for E3D Clone or Genuine hotends. It is an essential component on my MP Mini printers, enabling me to achieve higher temperatures when printing with PETG materials. ...The bolts...

I've been using this fan duct for my 3D prints, and so far, it seems to be working quite well for me. I decided to print it in high quality mode to make sure it lasts as long as possible - maybe I made a mistake though, since I'm still new to 3D...

It seems there were no MK8 Fang Fan duct part cooler so I grabbed one and edited it to work. So this is a remix but I can't find the one I snagged, I'll give credit if I find it again. This fits my RepRap Guru i3 with original MK8 hotend that only...

... think it's just mm to cm conversion wrong, anybody can tell me to fix i will. ...IMPORTANT, THE BACK PLATE NEEDS MODIFICATION TO ENABLE THIS TO FIT PROPERLY, I CUT THE FAN STANDOFF OFF BUT MAY LOOK INTO REMIXING THE PLATE TO ENABLE THIS TO FIT CLEANER.