4020 fan 3d models

This is a 4020 fan duct made to attach to the Klemco Hotend Mount. This design allows the fan to fit close up against the mount by having an M3 cap-head screw recessed into the sliding bracket. This part should be printed in PETG or ABS to avoid the...

... and a pressure clip that he designed. ...I also took a look at his creation, which is a bit more rough around the edges than the original, but it still manages to hold an 4020 fan in place with ease. ...Overall, I think you'll find it quite useful!

Minor refinements This is a mod to replace the OEM part cooling fan for a 4020 fan & ABL sensor It involves cutting away a small section of the OEM hot end housing sheet metal (cut area shown in pic) however it is reversible should you want to go...

Designed to accommodate my BLTouch clone plus a 4020 fan. I tried a few other designs here but didn't like any of them. I've been using this for over a month and it works flawlessly. Printed PETG. Minimal support required for one part only. I...

The Ender 3 fan duct is a custom solution designed to accommodate two 4020 radial fans, providing efficient airflow and temperature management for this popular 3D printer model. ...This ducting system enables users to optimize their printing environment...

A dual axial 4020 fan support + duct for Sprite extruders (should work on plastic version too, printed for all-metal) Requires a zero-offset BLtouch mount. Assembly: 4x20 M3, 8X30 M3. The three components (duct/support/cap) should be glued with...

Parts needed: 2 x 4020 fans 1 x 500 mW laser screws/nuts 3mm (can re purpose items from fans) Used this fan test to check cooling from TeachingTech: https://www.thingiverse.com/thing:3167063 Assembly tip: Counter sink holes on the exhaust side of...

To do this I've searched for a replacement hot end cover that will accommodate a 4020 fan as the standard cover is just a little bit small. Having not found anything suitable and as I want to keep the look of the standard cover whilst still utilise...

This is a remix of the Satsana original fan duct adapted for the Longer / Alfawise stock mount and also a 4020 Sunon fan instead of the 4010 stock one at the hotend cooling. It also features a 18mm inductor sensor holder. This is a work in...

It works with the 4020 fan. It lines up better with the OEM blower fan intake. (See my other hotend cove rif using standard fans) This will work with the standard fans but will leave a gap between the cooling fan and hotend. Oh yea it also holds...

We have done comprehensive CFD to ensure this is the best duct possible for the stock 4020 fan. This new Volcano V3 duct utilizes 90% of the available flow from the 4020 fan. This is the best duct we offer for the stock X1 extruder setup. See...

Here is a bracket to mount a 4020 Fan to cool the main board of a CR10S Pro V2 printer. As the CR10S Pro V1 has more or less the same mechanical structure, this file should also work for this printer. To mount the fan, you will need 2 M3x6 screws...

Ender-3 v2 4020 fan user! If you want more lighter head. Try this duct. Use the included .step file to remix to your heart's desire! ▷ Update fan wind test new movie (22-3-19) Regarding the issue of the installation angle of the filament...

Insert 3 M3 nuts into the back of the cooling fan part of the mount and lock the 4020 fan in place using 3 m3x16 bolts. 3. Connect the fan to your motherboard and modify your machine's firmware. Enjoy the additional cooling! ...Any additional...

I already had 4020 fans onhand because they do the job as well. Where the 5015 fan sits on the Blokhead is directly underneath the Extruder Motor when using MDD v1.3 (direct drive) with the OEM extruder. It fits in the base of the Blokhead very...

________________________________________________________________________________________________________________My other Ender 3 V3 SE modsFan mods:Ultimate Ender 3 V3 silent upgradeVoronoi fan coverPrinter mods:Tool holder Filament spool...

I've also removed the 4020 fan posts from the original design and widened the holes to M4 size, as those posts always snapped off immediately for me in the original version; I've also widened the left side cable gap to accommodate a display cable. ...

We have done comprehensive CFD to ensure this is the best duct possible for the stock 4020 fan. See pictures for more information You will need to print: 1x Duct part 1x BLtouch Mount (note: there are two lengths, print both and try) 1x BLtouch...

We have done comprehensive CFD to ensure this is the best duct possible for the stock 4020 fan. See pictures for more information You will need to print: 1x Duct part 1x BLtouch Mount (note: there are two lengths, print both and try) 1x BLtouch...

4020 fan adapter that fits inside the original CR6 hotend cover. Provides a lot more airflow so the fan doesn't need to run at 100% all the time (40% is about the power of the original fan). It is required that you remove the upper part of the...

We have done comprehensive CFD to ensure this is the best duct possible for the stock 4020 fan. See pictures for more information You will need to print: 1x Duct part 1x BLtouch Mount (note: there are two lengths, print both and try) 1x BLtouch...

I made this to slip over a 4020 fan on my 3d printer, it's got half a hinge I use for mounting a raspberry pi camera module.  When I printed this I printed it with 100% infill as I wanted it strong and its walls are thin. I was over extruding...

For this mod, in particular, there are multiple images attached to this page which annotate what you need and where.For the 8.35mm sleeve bushing, you can just reuse the bushing on the existing Ender 3 X gantry V-rollers.Hardware10x M3 Nylok Nuts (6x...

<p>Easy and fast fix to get a Bigger and silent Cooler into your system. ...BLTouch and other mods should still work as before because its only a bit deeper to the front.&nbsp;</p>

Customized version of https://www.thingiverse.com/thing:21112 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=21112

Customized version of https://www.thingiverse.com/thing:21112 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=21112

Customized version of https://www.thingiverse.com/thing:21112 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=21112

Here is a 3D model of the extremely popular 12-volt turbo fan 4020. ...You can use it to create your own 3D assembly models with ease.

protective shield for a 4020 radial blower, perfect for avoiding stray filament pieces and other ooparts from damaging the cooler.