4010 fan 3d models
130603 3d models found related to 4010 fan.
thingiverse
4010 model fan mount and duct for a Mellow BMG Wind extruder ( https://aliexpi.com/twlM ) Suits Ender 3 stock fan Used M3x16, M3x55 and M2.5x12 DIN912 screws. ... UPD 21.12.03 Updated mount a bit Added a simple fan duct as my airflow calculations were...
myminifactory
This is a versatile stock cr10s (4010) fan mount for v6 clone hotend mounting (check out my files).\r\nIt boasts impressive clearance, adjustable slots allowing for effortless height adjustment whether using a v6 or volcano setup. ...The 4010 fan simply...
thingiverse
I use a Volcano heater block, and the existing 4010 fan designs don't go low enough to blow to the nozzle. ... I used this piece as the base and just extended the arm so the fan can go lower: https://www.thingiverse.com/thing:5175934 it's a RIGHT SIDE...
thingiverse
It's a straightforward conversion from the 3010 fan to the 4010 fan. To use, simply print out the adapter using ABS plastic and then glue it securely onto the 4010 cooler using super-glue. ...Insert it as shown in the picture - that's all there is to...
thingiverse
This is a modified version the VORON Switchwire fan duct to mount it to a stock Ender 3.I used two 4010 blower fans mounted back to back for cooling the part, and far the heat break it remains the stock 4010 fan.You may find that mounting the blower...
prusaprinters
________________________________________________________________________________________________________________My other Ender 3 V3 SE modsFan mods:Ultimate Ender 3 V3 silent upgradeVoronoi fan cover Printer mods:Tool holder Filament spool...
thingiverse
This bracket mounts the mainboard fan that is currently bolted to the bottom cover directly to the mainboard and adds an additional 4010 fan. You remove 3 mainboard mounting screws and replace with bracket & 3 M3 SHCS. I wanted to be able to cool the...
cults3d
The 4010 fan simply slides into place without needing screws to secure it, although there are holes available if you prefer to use stock screws. I've personally run this mount without screws and haven't experienced any issues, even with the fan not...
prusaprinters
I added a new bracket to hold a 4010 Blower Fan to cool down the xStation when in use.This is only for the SCPH-55xx versions!Fully compatible with LaserBear's SD Card...
thingiverse
This is a remix of Satsana Remix for Ender 3V2 and Ender 3 with BLTouch / 4010 Fan versions. You can get the other parts like the BL touch mounts from the original make. https://www.thingiverse.com/thing:4647053 This is my first attempt remixing...
prusaprinters
4010 model fan mount and duct for a Mellow BMG Wind extruder ( https://aliexpi.com/twlM ) Suits Ender 3 stock fan Used M3x16, M3x55 and M2.5x12 DIN912 screws. UPD 21.12.03 Updated mount a bit Added a simple fan duct as my airflow calculations were...
cults3d
Designed for M3 melt nuts and a 4010 fan. I mounted a grille (https://www.thingiverse.com/thing:2802474) on the inlet of the fan. and V13 for the grill on the outlet. ( https://www.thingiverse.com/thing:1750976 ) V15 is intended for the use of...
thingiverse
I deliberately chose not to use the old gen3 duct for the 4010 fan despite the creator's claim that it is backward compatible. Try printing this part as shown in the slicer screenshots: - Use a layer height of 0.16mm. - Select supports everywhere...
thingiverse
I wanted to keep it simple and make it lighter for my direct drive, the blower fans will snap in place without any screws and you will use the stock screws to mount it to the plate and to mount the 4010 fan. The micro swiss all-metal extruder...
thingiverse
Designed for M3 melt nuts and a 4010 fan. I mounted a grille (https://www.thingiverse.com/thing:2802474) on the inlet of the fan. and V13 for the grill on the outlet. ( https://www.thingiverse.com/thing:1750976 ) V15 is intended for the use...
thingiverse
With this you can connect a 4010/4020 fan to the laser head so that the fumes from the cutting/engraving are dispersed before they reach the lens. ATTENTION! when using the fan you cannot use the red acrylic cover, so you must always wear glasses...
thingiverse
4010 fans (40mm x 10mm) fit snugly in place and use M3 screws to hold, but I drilled them bigger because I wanted to use screws I had on hand. It may be compatible with an ender 3 hotend but can't confirm myself. It was brought to my attention...
thingiverse
so did a lot of work redesigning the mount, extended it to fit the 4010 fan between extruder and hotend PCB and also changed the mount position so that the nozzle is as close as possible centered from the carriage, else i guess you cant use the full...
grabcad
Отлично подходит для моделирования на основе этой модели. ...Высокая точность модели.
thingiverse
Human: 3D model turbo fan 4010 for 3D assembly use.\r\n\r\nAliexpress examples of fans:\r\n[NONAME fan](https://aliexpress.com/item/32995460483.html) [YOUNUON fan](https://aliexpress.com/item/4000072275637.html)
grabcad
Also, the thickness of the fan is slightly smaller than 10mm and the thickness of the housing is different.Part that I have :https://www.123-3d.nl/123-3D-Ventilator-24V-40x40x10-mm-radiaal-i4192-t0.htmlI adjusted these parameters and hence this...
thingiverse
... direct drive conversion. ... To assemble the direct drive mount, please visit the Thingiverse page at www.thingiverse.com/thing:3899870. For instructions on installing the V6 fan mount, see the guide located at www.thingiverse.com/thing:3899900.