4010 fan duct 3d models

4010 fan duct (presumably, CR-10). Plenty of these are sold on Amazon/eBay. ...Please note that mounting screws are M2.

4010 fan duct (presumably, CR-10). Plenty of these are sold on Amazon/eBay. ...Please note that mounting screws are M2.

&nbsp;&nbsp;Do note that this duct can be paired with my other side-mounted duct (also used with a 4010) for a very powerful airflow from two directions. The combo works quite well with my <a href="https://www.printables.com/model/271680">BIQU H2...

Dual 4010 Fan duct for Ender 3. Utilizes stock hardware (+ 1 additional 4010). ... Direct Drive compatible (low clearance) No supports needed when printed as shown in Image 3.

... mounted, fix positioned 4010 fan duct I've included on this design (my BIQU H2 carriage). ...It works very well with my other main fan duct.&nbsp;Feel free to comment with any issues; I'm always happy to help out another 3d printing enthusiast!&nbsp;

Dual 4010 fan duct for E3D v6 setups Optimized for ease-of-use and broad compatibility with different setups. If you have any requests or suggestions, leave a comment and I'll see what I can do! Features: - Unobstructed front, so you can see if the...

Dual 4010 fan duct for E3D v6 setups Optimized for ease-of-use and broad compatibility with different setups. If you have any requests or suggestions, leave a comment and I'll see what I can do! Features:- Unobstructed front, so you can see if the...

Dual 4010 fan duct for E3D v6 setupsOptimized for ease-of-use and broad compatibility with different setups. If you have any requests or suggestions, leave a comment and I'll see what I can do!Features:- Unobstructed front, so you can see if the...

Modification to Enhance Fan Duct Performance for Longer Nozzle Operation on A10M.

Motor mount for cr10, as well as my design of carriage； Modifiable step files available；

The fan duct is not perfect airflow-wise, but it was sufficient for me so far. Print lying on the mounting plate that will be screwed to your extruder. Supports needed only for the small part of the fan duct. ... Onshape design: ...

Inspired by new cr-10 v2 fan shroud, now with dual 4010 part fans..

Inspired by new cr-10 v2 fan shroud, now with dual 4010 part fans..

... PETG or Polycarbonate may be better. For the best cooling, 2 need to be printed so you can mount 1 fan duct on either side. ... **Hardware needed:** 2x M3 x 16 screws 2x M3 washers *You can use 4 screws & washers but I found it unnecessary

Allows better directed air flow to the nozzle, and overhangs up to 85° with dual ball bearing 9000 RPM 4010 fans. Use M3x6 screws to attach to the existing fan ducts. I didn't have spares, that's why in the pictures I use printed M3 pins to attach....

Made this fan duct for the Biqu B1 after I changed the heat-break and nozzle to a volcano style. Fits the stock 4010 blower fans. No screws necessary. These are the parts I used that I got off Amazon. As an Amazon associate I earn commission...

"Triplafan 4010" modification for Tevo Little Monster.

This is a modified dual outlet fan duct that I adapted from sirhcwolf's original design to work seamlessly with my fan shroud for the JGMAKER MAGIC. My fan shroud can be found at https://www.thingiverse.com/thing:4426539. You can also find...

My fan shroud can be found here: https://www.thingiverse.com/thing:4426539 sirhcwolf's single duct can be found here: https://www.thingiverse.com/thing:4457668 I have tested the Dual duct on a 150mm bridging test and got better results than I had...

4010 model fan mount and duct for a Mellow BMG Wind extruder ( https://aliexpi.com/twlM ) Suits Ender 3 stock fan Used M3x16, M3x55 and M2.5x12 DIN912 screws. ... UPD 21.12.03 Updated mount a bit Added a simple fan duct as my airflow calculations were...

4010 model fan mount and duct for a Mellow BMG Wind extruder ( https://aliexpi.com/twlM ) Suits Ender 3 stock fan Used M3x16, M3x55 and M2.5x12 DIN912 screws. UPD 21.12.03 Updated mount a bit Added a simple fan duct as my airflow calculations were...

This is a remix of The Satsana Fan Duct for a 4010 (stock) fan for an Ender 3v2. This version is modified to integrate with a mount for a 500mW laser and BL Touch. There is also a Honeycomb cover for the 4010 fan. ...Step files provided to customize...

This is a modified version the VORON Switchwire fan duct to mount it to a stock Ender 3.I used two 4010 blower fans mounted back to back for cooling the part, and far the heat break it remains the stock 4010 fan.You may find that mounting the blower...

You can use it with stock 4010 fan.. ...until you'll get 4020:)

You can utilize it with a standard 4010 fan initially, then upgrade to a 4020 when available.

I deliberately chose not to use the old gen3 duct for the 4010 fan despite the creator's claim that it is backward compatible. Try printing this part as shown in the slicer screenshots: - Use a layer height of 0.16mm. - Select supports everywhere...

someone was interested in my 5015 duct but using the stock 4010mm fan so i designed this. any questions just ask! =] id recommend pla for the bridging properties over petg. ...you should not need supports if you face the top (long flat part) on...

Needed a new fan duct. Couldn't find one similar to the old one, so i quickly designed it, and crappily printed it, might use a more heat resistant material in the future, but i figured that it was far enough away from the hot end that it wouldn't...

Made for my Ender 3 Max but I believe it should be compatible with any Creality printer with a 4010. Post your makes on different printers and I'll update this post with printers that it is confirmed to work on. I will say this though, on the max the...

this is a remix of https://www.thingiverse.com/thing:4693548 I only added a bl touch mount and made a spacer block to go with. ...going to test this myself soon. keep posted. wil be adding a cover for a Noctua nf-a4x20 flx front fan later.