4 inch duct 3d models

... 4-inch exhaust fan on a wall. ...Given my possession of a 3D printer, I figured it would be easy to quickly print one up. This approach worked out well, so I thought I'd share it with others who might need to hang a dryer vent or any other 4-inch duct.

general 4 inch duct interlock to connect to various ventilation spots.print the tube side with the locking mechanism facing up, and the flat side of the panel downLikely not standard pattern with commercial versions, may update in the future,

... purpose. ...It is printed on a JG Aurora A5S, with 0.25mm extruder and 0.1mm layers and a 4mm Brim. it is designed to fit over a 4 inch aluminum duct and fixed in place using wood screws. ...This was originally designed for my Glowforge installation.

... Decided to add some support to the 4 inch round duct on both sides. This uses a #8 screw into plastic wall anchor. Added a 2nd Beefier Version of the same model. ...This one has two screws.Uses 3.52m of filament and takes 1h6m at 0.2mm Quality.

Caps for a 4 inch inline duct fan.

A 4 inch duct fan cover. ... Wrap 1 piece of electrical tape around the inserted portion to make it fit snug and provide friction for grip.

This is a 4 inch duct 2-to-1 splitter that is fairly compact and easy to print.No supports needed.See also the Endcap model here: https://www.printables.com/model/637194-4in-4-inch-duct-splitter-endcapSource document:...

This covers the end of a 4-inch duct in order to keep critters from crawling into it. It fits *inside* the *crimped* end (the "male" end of a connector or elbow). You could size it up a tiny bit to fit in the larger "female" end of the duct. ... ...

This is a duct hose holder to allow you to mount a 4 inch duct hose along a wall or floor without needing to screw anything into the wall. Instead, simply use a "Large" size 3M Command Strip adhesive to mount it onto the surface. This allows you...

The worker requires a four-inch duct for the DAL project, specifically a four-inch bullnose prop printed in durable nylon material.

Adapter connects four-inch duct to one twenty by one twenty millimeter fan. Three versions available: slim, slim short, and standard. ...Slim short model measures ninety-eight millimeters in diameter, slightly smaller than the standard ninety-nine...

Pipe hanger for round 4" duct pipe. provides a tight fit that lightly snaps into place. Holds pipe off the wall about 1-¾", which was perfect for aligning with the inline fan I had. Be careful not to overtighten top screw. ...Worked like a charm for me...

Mounts directly onto a standard 92mm fan and securely connects to 4-inch ducting systems.

If you have some unconnected 4 inch duct that needs an end cap, then this is the model for you! ...Slide the duct over the opening and then use a ring clamp to hold it in place.

4 inch air duct adapter for the Halot One. ...I used two screws and electrical tape of the left side where there is no screw hole.

I'm running 2 Noctua Redux-1700 PWM fans between 6 and 7.5 volts and it manages to push through 2 draft blockers (Canada Woo!) and about 25 feet of 4 inch ducting (with 3 elbows and 2 bent flexible ducts) with ease. I've included 2 high quality...

Here is a sturdy 4" duct flange to facilitate seamless connections between 4" round duct work for efficiently exhausting whatever you need. I utilized mine to exhaust fumes from my K40 CO2 laser with great success. I used 6-32 x 3/4" machine screws,...

It shares exhaust with the dryer and some air went out and some toward dryer even with a Y duct. Built one for each and to keep cold air out when not in use. Using one for the make up air for the furnace intake also. The box is designed to be easily...

A simple 4-way duct splitter scaled for 100mm or 4inch ducting. Strong enough for metal clamps. ...Extract via the top and split the other 4 lines to whatever you need to remove heat from.

I've decided to upload the most useful part of my heat ducting setup, but if there's interest in other parts like holding a 1/2 inch foam board in a window or using simple 4-inch exit adapters on the foam board, just let me know and I can add them or...

This is a 4 Inch Hose Quick Disconnect to Union.

... be required. PDF explains the parts and easiest way to assemble.Found the Duct plate had two models in the .3mf. Fixed and also increased outer diameter of plate duct to minimize lip around 10mm up. ...And changed all to 0.2mm Quality profile.</p>

This is a shroud for a large carbon filter, 7 inches in diameter. It covers 100 degrees out of 360. I have a fan pulling air out of the filter because it has a fabric filter on the outside. I wanted to retain the use of the fabric and keep it on a...

Fits AC Infinity Cloudline Inline Fan 6 inch to 4 inch duct.

This is a remix of an existing 120mm fan to 4-inch duct adapter. I made two adjustments to the model: 1) I removed the existing duct port which was 109mm wide and replaced it with a standard 100mm port, this should be more compatible with more...

Designed for a 120mm fan to fit a standard 4-inch duct (Dryer Duct), ensuring airflow. Its construction ensures no support needed and easy printing. It can be placed in the middle of the duct or inside the enclosure. I added 4 holes to add zip ties...

I fabricated an enclosure for my Anet A6 and required ventilation so I created a support to hold the fan and the 4-inch air duct. The part fits snugly onto the crimped end of the air duct, allowing you to increase the radius of the duct support if...

I'm utilizing a 4-inch daisy wheel to convert a 4-inch duct stopper into a controllable vent. Initially, I encountered difficulties regulating the exhaust fan speed on my K40 laser cutter, prompting me to create this device. By integrating the daisy...

This is a wall-mounted, mostly-hidden support for a 4-inch dryer duct. There is a version that has the mounting screw at the top and one with the mounting screw at the bottom. ... You can edit this for free on Tinkercad:...

Designed for use with a Creality enclosure, but will work for any 4 inch duct. The purpose is to vent toxic ABS fumes from the enclosure to the outside.</p><p>On the Creality enclosure, a 24V 5015 fan was used, powered by the 24V power supply from...