3rd party firmware 3d models

3rd Party Switch Dock with a Key for fixing the Hub Cable## Buy Switch Hub here: https://www.amazon.de/RREAKA-USB-C-Hub-5-6-IN-1-4-1-HDMI-USB-C-HUB/dp/B07NN8XCJF Printed without any Support

... 6mm toilet seat screws are to be fastened. ...Just print the plugs and add them to the 6mm threaded rods on the 3rd party seat, then reinstall it on the toilet. No more moving around. Very simple design, I agree. However, it works flawlessly. ...

Spacer for 3rd Party Version of the Manfrotto 323 Base Plate. As the base plate cannot be mounted to flush surfaces, I designed this spacer. It also accommodates the space needed by the tiny locking mechanism (6.5mm thick version, see photos). Due...

When I switched from my Clark Pads that was 1 big pad to Grizzla pads that are 2 smaller padsI noticed that they had a tendency to move around a bit due to smaller velcro area so I made this version to make it stay in place better. A simple yet...

I discovered that third-party BL touch units, equipped with a connector on their rear, do not fit the original lower cover component of the Toronado extruder. After making some adjustments, I was able to ensure that any BL Touch unit will now fit...

Unlike official NES dogbone controllers, third-party ones such as this Tomee controller do not have a pivot for the D-Pad to rock on physically, which prevents opposite directions from being pressed at the same time. This results in strange behavior...

This is an adapter for 3rd party straps to make the strap more compact and comfortable. ...It raises the strap by a few cm and allows for it to compact down a lot better.

To use a 3rd party filament spool with the UP! Mini printer, an alternative shaft must be designed since the original one is too short and wide. Failing to adhere to the given instructions may result in damage to the printed part due to its...

Here are some very popular upgrade parts for Hercules, a 3rd party Devastator made by TFC. I've added a bunch of parts in one file, you will likely need to split these out and reorient them. Included are: Thigh extensions, which add 16mm of height...

These are brackets are adapters that raise the height of the second generation 3rd party elite straps commonly used with the Oculus Quest 2, they allow for weight to be better distributed and also for the back cushion to properly engage with the back...

I finally took matters into my own hands regarding the annoying gap that persisted under nearly every third-party antenna or adapter on my trusty FT-60 (which unfortunately isn't flat, ruling out a simple washer solution) and created a spacer to...

Spool holder design allows for third-party standard filament spools to be mounted to the Dremel 3D 45 internal spool housing. WARNING: Ensure that the retainer bolt is fully secured before printer operation. Protrusion could interfere with build...

Artillery Sidewinder X2 - Marlin 2.1.1 Firmware UPDATE Nov 3rd. Just activated second stepper driver for double Z axis and G34 - Z Steppers Auto-Alignment. It will only works if you install a new stepper driver in your mainboard and connect each Z...

This is a rather straightforward spool holder that I constructed once I obtained a spool of PLA filament, as Da Vinci printers don't allow the use of much easier, cheaper and better quality materials since they aren't open source. Given this fact, I...

... was created using Customizer! ...(http://www.thingiverse.com/apps/customizer/run?thing_id=162367). The specifications used were font size 19, label text as '3rd', an end space of 1, the 'write/Letters.dxf' font style and a letter spacing of 1.

... you can adjust parameters such as font size (set to 19), end spacing between characters (set to 1), and letter spacing. The chosen font is "Letters" and will be saved in the .dxf file format. The label text for your customized item will read "3rd".

Bigger hole to support 3rd party USB-C cable for AirPods like https://www.amazon.de/gp/product/B08KXQFM43. ... Bigger hole for Gen5 Apple Watch USB Plug fron remix https://www.thingiverse.com/thing:4390212

Bigger hole to support 3rd party USB-C cable for AirPods like https://www.amazon.de/gp/product/B08KXQFM43. ... Bigger hole for Gen5 Apple Watch USB Plug from remix https://www.thingiverse.com/thing:4390212

This is a premium charging stand designed specifically for third-party chargers of Garmin Fenix watches. You can find the charger at: https://www.amazon.com/gp/product/B07L3TQP9B This project was inspired by and reimagined from: ...

This slingshot versatile for various projectiles to hit targetsThis is the latest current slingshot of Tim Postma (Windsor , Ontario Canada)as of december 19th 2019 & is released for transparency & as a regular releaseThis slingshot versatile...

The HP OfficeJet Pro 8710 model's infinite chip is secured by a holder. Using the Chip Holder has several advantages: The chip's movement is eliminated, ensuring a stable connection point. ...Errors or damage to the chip are prevented.

A 1 kg aftermarket filament spool spool holder, featuring a 20 mm spindle, is available. ...The holder can accommodate spools up to 94mm wide and includes a cutout for fitting around the Up Mini CPU cooler mod.

The spool in the peg well is too small to support these heavy 1kg spools. This only works with spools that are exactly 96-97mm wide. ...It will not function properly with Hatchbox, Esun, or Amazon Basics spools.

I created this mount because I needed a way to securely attach my Raspberry Pi to my printer, all while keeping the same protective case in place. Noticing that the printer had mounting holes on its back panel, I decided to use those as a starting...

Due to ongoing changes at yolasite.com affecting firmware downloads, the firmware download URL has been updated to http://s3.amazonaws.com/sailfish-firmware.polar3d.com/release/firmware.xml. This firmware includes many new features, including...

The firmware was developed by Dan Newman and Jetty, with roots in a derivative of firmware released by Makerbot Industries. As it is not an official Makerbot release, any updates will be posted on the website, so check back often. ...Don't forget to...

This is a dash mount for an aftermarket CarPlay screen for the ND Miata.

I highly recommend against printing it on the Up mini itself with ABS due to warping issues. It's better to opt for PLA instead since it doesn't warp. You can also consider using a 3D printing service if you don't have one at home. ...Try to use...

This is a spool holder specifically designed for 3D Systems' CubePro 3D Printers, perfect for users who frequently employ Esun filament, such as PLA+, without any issues. ...For enhanced performance and reliability, I highly recommend pairing this spool...