3rd gen 4runner 3d models

This is a custom 3d print model I made for the toyota tacoma. it snaps in place just like the oem. I would recommend you print it in abs for it to withstand heat unless your in a cold environment. ...message me if you want to customize it or ask me any...

Here is a radio plate for an 82-92 Firebird designed to fit a Double Din radio. The design incorporates the dimensions of a real radio plate, ensuring a proper fit in most cases. However, I don't have personal experience with a Double Din radio in my...

Support for elevate rear suspension for third generation Honda CR-V. ... I used PLA and painted with something to protect from water.

Combination of https://www.thingiverse.com/thing:3693385 and https://www.thingiverse.com/thing:4038181

Wall Mount for Apple TV Remote, Third Generation. The remote is angled at approximately 15 degrees, making it easier to grasp the device. ...Print Settings Printer Brand: RepRap Printer: Mendel i3 rework Rafts: Not required Supports: Enabled Resolution:...

This plug fits into unoccupied switch holes in a central control panel, and it was made as a replacement for one that had gone missing.

Slide on stand for iPad Pro 11 inch. Designed to lock at four positions (0, 45, 90 and 135 degrees) with a spring mechanism. Spring dimension is given in pictures. Print instruction: No supports needed for all parts. Parts with threads should...

The 3D model was accurately built on a real foundation. It's constructed precisely, using actual units of measurement, and it matches the original model qualitatively and as closely as possible. Model formats include: - *.max (compatible with 3ds...

This is a switch holder that replaces the coin holder in the center console. This was specifically designed for the push button switches that come with Auxbeam off-road lights but I believe its a common switch size. Its just using the sticky tape...

<p>There are two versions of the model. One is just a blank for the center console. The other is for a flush mount USB port.</p><p>Models are set in the correct printing orientation. The clips do not need supports.</p><p>For the USB model use the in...

<p>These mounts allow the replacement of the stock dash speakers with 3.5" aftermarket speakers.</p> <p>I designed these around the Infinity Reference REF-3022cfx 3.5" speaker - compare your speaker specs to these to see if the mount might work for...

To be used with factory rubber inserts, the insert for the 12 oz can will work just fine with the 8.4 oz can. ...If you like the better fit and are exclusive to the 8.4 can print the one for 8.4.

Cup Holder Compatible with 1997 Toyota 4Runner Models, May Also Fit Other Vehicles

Adapter assembly to remove TomTom GPS and insert an iPhone in place of the head unit.Toyota 4runner Gen4 (mine is 2009 SR5)Toyota Tacoma Gen4Download the STL file and print or order at any online 3D printing service.

I was on the hunt for a replacement hub-cover that matched my 1997 Toyota 4Runner's wheels, but couldn't find one, so I measured up the old one and decided to make a copy in plain black. After some trial and error, it seemed to turn out pretty...

This mount lets you swap out your current sunglasses rack for a six-switch sPod on your 5th Gen 4Runner. Please note that this mod is specifically designed for vehicles without crawl control. ...If your 4Runner has a built-in sunglasses holder, it's...

This is a Center Console insert for a 5th Gen 4Runner.  I have it in a 2022 but should fit other years.  Added Sasquatch for the kids.   Only use PETG or ABS. ... Follow directions for your favorite filament.

The existing badge holders seem to be designed for 1st and 2nd generation models. To address this issue, I created a 3D printable holder that offers several benefits. One notable advantage is the ability to install it without removing the grill. The...

WORK IN PROGRESS. Uploaded version has switches spaced just too far and won't fit in cubby hole. ... Took Cracked1's cubby switch panel and made it for 3 small size toyota switches, fits and works perfectly fine.

I needed to extend the cord to fit inside of the plug. Mine was a mile long and needed a bit more room to fit inside. Works well with the new print. ...Previous one by anewsome didn't fit and broke on the seam.

Here's a modified version of the design that accommodates an IT power supply by increasing the size of the hole. I made only one alteration to the original design, found at https://www.thingiverse.com/thing:3273420, to allow for the use of an IT...

This part slides onto the existing volume knob. For me, the friction fit was perfect with my print - no glue was used. Your fitment results may vary though. It may wilt during the summer heat. ...We shall see.

I designed a replacement part for my 2012 Ford Focus's worn-out parcel shelf hinges, specifically targeting the inner (center) component. My goal was to create a larger surface area that can be securely attached to the possibly damaged parcel shelf...

Simplified version of leefla's design, made to hang from the top of a dresser. Rather than designing the correct sized hook, I left that part of the model flat, so that a hairdryer can be used to soften the plastic and then mould it by hand...

I created a custom replacement component that transforms the side dash pocket into a sturdy shelf, specifically engineered to securely hold a brake controller. ...This innovative design is tailored to accommodate the Tekonsha 90160 Primus IQ Electronic...

I added a cable organizer to the base, giving it a fresh remix of the original V2. Still utilizing PLA/PETG, one of the two small tabs in the middle section tends to break often, but it will still snap together securely. My build time came in around...

Remixed from the following models: https://www.thingiverse.com/thing:3224790 https://www.thingiverse.com/thing:1873213

Are you one of the three other people on the planet who have a 2019 Honda Fit and a Galaxy S20 Ultra in a Spigen Neo Hybrid case, hate generic phone mounts, and are into 3D printing? Well, I've got the design for you! Seriously, I am really picky...

This is a redesign of Litesaver's original cupholder. This cupholder has been redesigned to fit larger cups. The original could only fit small water bottles and cans. With this new redesigned cup holder, you can now fit much larger drinks from fast...

The new Alpas Generation GW - L by Ziegler . This Modell contains a Detailed Exterior and Interior. Arround the Construction are Detailed LED - Stripes for surrounding lighting. ...Only the Parts from the Pictures are Included in this Draft!