3rd gen 4runner cup holder replacement 3d models

Cup Holder Adapter for 3rd Gen Toyota 4Runners. Specifically fits 32oz Hydroflasks. This part prints in two pieces. ...They're meant to fit tightly together.

I was tired of the cup holder in my 4th gen 4Runner so I took some measurements and estimated the general shape of the cup holder opening. My print ran out of filament at the end but worked as is, so the actual model might be a little tall. ... ...

It's specifically made for holding a tapered cup, like those used by Starbucks, and features a single cup design. The core render takes into account the locking tabs that attach to the pockets on the back of the holder. To accommodate different uses,...

Cup holder fits inside the rubber cup holder insert for the 4Runner. Best fit for the cup holder near the front. You must have the rubber OEM cup holder insert for this to fit properly. Super Glue the base to the top, off set from the center,...

The 3-inch spacer kit for the 3rd gen Toyota 4Runner offers unparalleled elevation for improved performance on the trail. Specifically designed for the front end of this model, it brings 3 inches of added lift. ...By making room between your suspension...

plug for the firewall on a 3rd gen 4runner. typical spot behind the driver side valve cover. The holes are for 8 AWG wire (~6.5mm) I used TPU. I'm not sure this would work with anything else? Especially the holes. ...they are made to seal against the...

(1) The adapter plate: This fits into the original holder's spot, partially recessed in the pocket for added stability, using the two factory screws for attachment. It also has back pockets for four 1/4-28 nuts. (2) Mount plate: This plate attaches...

This custom cup holder is designed specifically for 3rd gen Honda Accords, which did not originally come equipped with any cup holders. It seamlessly replaces the face plate on the ash tray, conveniently located underneath the stereo system. To...

3rd gen 4runner (1st gen tacoma potentially) frame scan with front suspension pickups, differential, and steering rack

This is a Rola roof rack adaptor for a 3rd gen 4runner. ...This will use 1/4-20 hardware.

5th Gen 4runner cup holder reducer insert to replace the stock one that gets stuck on the bottom of mugs then lost forever. Made from scratch in freecad. The small without handle is perfect for contigo mugs. The large without handle is...

Replacement shifter bushings for a 3rd gen 4Runner. ... I know they are pretty cheap as it is but what the heck, it's a Sunday, I'm bored and wanted a project as my shifter is really starting to annoy me...

Check out this forum post for detailed information on the part and its creation process: http://www.toyota-4runner.org/3rd-gen-t4rs/246409-finally-3d-printed-sr5-mudflaps-flare-end-caps-free-download.html. ...You can also download full-size mudflaps...

Rear Hatch Support Bracket for a 3rd Gen 4Runner. Prevents the rear hatch from sagging due to worn-out or damaged struts. Secures in place with a snap fit. ... Measures 8.5 inches long for full strut extension.\nPrint Settings\nPrinter Brand: Robo...

Replacement fuel spring clip for a 3rd generation Toyota 4runner. This model is the plastic portion the fuel door.&nbsp;</p><p>Initial print was in PLA, but warmer weather will warp PLA over time. ...Petg is preferable in this case.&nbsp;</p>

Toyota 4runner 3rd Gen rear bumper , only renders.I sell the files as DIY kits, including cutting and folding files. ...These are for personal use only so they cannot be commercialized or shared with third parties as they are protected by copyright.All...

This print is designed for any late 3rd Gen 4Runner center console, whether you simply want more switches available or you've swapped to the new console to get cupholders and don't want to lose your center switches. I created this switch plate...

This print is for any late 3rd Gen 4Runner center console, whether you just want more switches available or you swapped to the new console to get cupholders and don't want to lose your center switches. I made this because, when switching from my '96...

Left and right arms for center console lid in 3rd-generation Toyota 4Runner vehicles. When I installed it, I had to sand down the tip of the pins to get them to click into place without breaking the mounts on the console lid itself. ...Your mileage...

These things inevitably wear out and, to my knowledge, no replacement is available for purchase. There are two models - one like the original bushing design, and another that I think works better under the circumstances. The first picture shows...

You'll need to remove the original mount and replace it with this one in order for everything to work properly. The mount is angled at 40 degrees, giving you an optimal view of what's behind your vehicle. Although I designed this specifically for a...

Use a 27-inch piece of 1/2-inch PVC pipe to link the two side rear mounts. Drill holes for #8 5/8-inch countersunk head sheet metal screws (They function adequately in plastic). Trim the sunroof's headliner trim forward of the mount for width...

3rd gen 4runner Rola Roof rack mounts

Print upside down for no supports. Holes are different sizes to fit different size drinks. Added version 10000000 with 2 85mm holes for the ungrateful peasants. I haven't printed the new one yet though. ...

Working on designing a phone holder for random compartments on a 2020 4runner. ...This design is for a wireless charging puck.

With this new redesigned cup holder, you can now fit much larger drinks from fast food restaurants. A large taco bell cup is shown in the picture, and it fits very nicely. This new design also fixes various design errors that the original one had. ...I...

I designed a coin holder for the 5th gen 4Runer pocket left of the 4wd shift. That pocket is pretty useless as-is. It'll hold about $8 in quarters. If you'd like to redesign your own, the dimensions are as follows: 2.5" long, 1.4" deep, 0.574"...

A compact replacement single switch panel tailored specifically for 3rd generation Toyota 4Runners, designed to seamlessly integrate into the switch panels found on the left side of the steering column. ...These units are perfectly suited for round...

These mounts were designed to attach a Rola V-Tex/Vortex Roof Rack directly to the factory roof rails of a 3rd Gen (1996-2002) Toyota 4Runner. These eliminate the factory crossbars and allow it to be mounted much lower than with the original mounting...

This is a plate that is designed for the rear speakers of the 3rd Gen 4Runner. These were specifically designed for the JVC CS-J620 Speakers but most 6.5 inch car speakers should work. The only extra part you will need is a slightly longer screw that...