3m 3d models

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

 You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid.  This can be...

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

A few copies of it will be printed, for two reasons: cooling during print and as spare if some print fails. raketplattform överdel_xy0.4mm_z0.2mm_ELIXIR_ELIXIR_ELIXIR_ELIXIR_ELIXIR.3mf raketplattform...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 3 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

The STEP file is included for easy remixing. Please post any makes and if you see a problem please post a comment. Updates: 4-30-2020: Thanks to feedback, I corrected the model for the base, the updated version is "6I". ...None of the other parts...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

... The single-blade model can be reversed in most slicer programs to cut from one side or the other of the 120 film, as described earlier, in "Preparing This Tool." The OpenSCAD source file therefore lacks any provision to make this adjustment. ...

I was unaware that the MMU2S required changes to the extruder and almost decided to hold off and just install the SPA by itself, but I started poking through the assembly manual for the MMU2S and realized there were changes that needed to be made to...

In short, it means that we will be using the Name Tag creator  to make the base (and thus be able to add text, image files, &c), and then create fitting covers and holders in this program. (A mixed approach is to also create the base with...

There is now an uploaded drilling guide that takes that into account. Update 8: The long awaited instructions document is now uploaded! Update 9, uploaded an updated Taz 6 specific endplate. There are several other related projects that are...

The grey color blends in nicely with the color of the grouts of my wall.4x screws 30mm x 3.5mm (+ 2 extra for version with customizable adaptor)4x screws 16mm x 3mmShort iron wire to be used as axis for front hinge2x screws 60mm x 5mm for mounting to...

A take on norwegiancreation's PID ball balancing seesaw using an Arduino.Video of this...

A steel axle would be overkill but a 3D printed one is replaced in minutes and you can use anything with a diameter of 5mm as an axle.Tighter construction -&gt; less wiggling of the parts. Feels sturdy.</li><li><strong>No need for support</strong> in...

:)All of the parts in this project are designed to be 3D-printable without supports, and they're modular, meaning you can choose how many "planter" modules to put together to build your tower.The planter modules come in two varieties: modules which...

No short circuits between the V G and/or S wires. Hardware I used these end-stops: https://aliexpress.com/item/32959048821.html I am not affiliated with AliExpress nor TwoTrees and there are LOADS of identical/rebranded switches out there. You will...

*helps: complicated objects, not designed for 3D printing* **Raft layers** `(2-4)` can not only help with bed adhesion but also can help with technical prints where even first few layers need to be accurate. When you add a raft all the first layer...

Print instructionsCategory: 3D Printer Parts Summary I've been enjoying using the stock inductive Z endstop as a bed probe on my Artillery Genius, but was suffering a bit from its temperature sensitivity: I was noticing that at different times of...

Beim ChaosRun handelt es sich um ein kleines 3D gedrucktes LED Spiel für den kleinen oder großen Zeitvertreib und je nach Spiel für bis zu vier Spieler. Die Grundidee habe ich von hier übernommen:...

If you want detailed instructions with pictures, please see my instructable on http://www.instructables.com/id/The-Bicycle-Bubble-Machine/ Apart from printed parts, you will need: a piece of wood to mount the machine on, which will then be put onto...

This is my design of a toy meant to teach children about the effects of an inclined plane on a rope/pulley system and the forces involved.  There are 4 3D printed parts in total and 7 externally sourced common hardware materials.  OpenSCAD Source...