3dsets

printable version of the 4WD badge from the Toyota FJ40 for the Model 9/10 from https://www.3dsets.com

printable version of the 4WD badge from the Toyota FJ40 for the Model 9/10 from https://www.3dsets.com

Alternative side steps, more beefy. ...Doubles as rock sliders. you can get the car at https://www.3dsets.com

Alternative side steps, more beefy. ...Doubles as rock sliders. you can get the car at https://www.3dsets.com

A playmobil boat fits(clips on) on the trailer. Print instructionsCategory: Toys & Games Summary Created a Towbar and a trailer for a 3Dsets landy( https://www.prusaprinters.org/prints/41264-landy-mini-by-3dsets ) Towbar is the same as for...

Fits to buggy from 3Dsets, diameter for tires 53mm. Designed for Tamiya OP-84 53084 - 6029 Square Spike Rear tires. ... Includes two separate bodies for easy 3d printing.

A 3DSets Minio Landy Spare Wheel Carrier drill a 7mm hole push through from the inside, a drop of cyno and push the wheel in place

Simple Frontlight Glass for 3DSets Bamboo Rc Car. Depending on your printer it should snap in place. ...Might need a superglue.

this is a modified wheel adaptor that will allow the use of the 3DSets Printed wheels with the RC Trailer. i made a mashup of the axle from 3Dsets and the original wheel mount from the trailer. ... this will need supports to print successfully.

Изменено крепление на стандартное как используется 3dsets: 2 болта M3*6 без шляпки и 2 гайки м3. Печатать из термостойкого материала, нейлона или HIPS. ...PETG и тем более PLA не выдержат температуру мотора (проверено)

A bullbar for the Landy mini from 3Dsets.com: https://www.prusaprinters.org/prints/41264-landy-mini-by-3d-sets No supports needed, they are pre-modeled in there in the spirit of the Landy Mini model. ...Just remove them.

VW Hub Cap for 3DSets Model 7 Buggy I have filled in the emblem with black paint for an original look. ... Printed with 15% Infill at 0,05 layer height on picture :-)

Simple Frontlight Glass for 3DSets Bamboo Rc Car. Depending on your printer it should snap in place. ...Might need a superglue.Use concentric top & bottom layers for more realistic look!

A trailer for the Landy mini from 3Dsets.com: https://www.prusaprinters.org/prints/41264-landy-mini-by-3d-sets There is a small trailer on: https://www.prusaprinters.org/prints/49214-3dsets-landy-mini-trailer But for me it was too small and it was...

Male driver is based off of: https://grabcad.com/library/the-male-figure-carl Female is based off of: https://grabcad.com/library/mulher-sentada-seated-woman-human-person-1 Scaled and modified to fit as a driver and passenger in the 3dsets jeep.

I found some makes already available, but the mount hole spacing on the motor I used (FlashHobby D3630 EVO “Turbo”) did not fit the holes in the other makes, so I made a new one from scratch using the 3Dsets' provided 4-hole adapter (printed, and...

... Scaled and modified to fit as a driver and passenger in the 3dsets jeep. ...Figures are recessed into the seats. https://www.3dsets.com/ Print instructionsLicence: Creative Commons - Attribution Category: R/C Vehicles Print Settings Supports: Yes

Saw this on a website for resto-modded FJs and thought this would fit the Model 9/10 from www.3dsets.com quite nicely uses M2x6 to mount exactly like the license plate holder. To mount the license plate holder to the jerry can holder you have to use...

Model is designed from scratch, based on Tube Doorsteps for Model 1 & 2Required screws for assembly:8x M3x102x M3x8 (rear screws)Intended to look good with accessory Tube Fender Flares for Model 1, 2, 6, but it will fit with the standard fender...

Saw this on a website for resto-modded FJs and thought this would fit the Model 9/10 from www.3dsets.com quite nicely uses M2x6 to mount exactly like the license plate holder. To mount the license plate holder to the jerry can holder you have to use...

Kahn Front for 3Dsets.com Landrover Defender Models. Match perfect with the Kahn Fenders: https://www.thingiverse.com/thing:4666076 No modification needed. You can exchange it with the Orignal Front, and reuse the holes for mounting the Kahn...

... 2275122. ...This part screws onto the press and has the shape of 3DSETS calibration print's ball joint pressing area. ... By using this part one can slowly screw the top screw and press the ball joint into the arms without damaging either piece.

I remixed the commercially available Landy from 3dSets.com, a fantastic project indeed! I removed the windows from the rear panels, just like you'd find on commercial or utility vehicles. The left and right files are identical, but they cater to...

I`ve made custome wheel hubs for the nice "offroad trailer" and the original 3dSets Wheels for the Landy and the Ranger. With this hubs, you can use 8mm rims instead of 11mm withoud making the track wider. ...You have to use 2x long M4 screws to screw...

This modified front bumper allows the @lukas_foukal snow plow to fit the 3dsets rancher. The included file replaces the servo guard on the original thing page. Use manifold, left, and right files from the original. No need to make any other...

Collection of mud flaps for the front and back of the 3DSets Landy.Overview&nbsp;Logo 4x4 Mountain.&nbsp;LandR. ...Logo.</li></ol><p>****</p><p>Printed with PLA and &nbsp;0.25 nozzle, color change at 0.65.</p>

Stand for 3dsets.com Landy 4x4 Wagon modified upper part for better vehicle balance and better fit slightly wider stand footprint for improved stability Print instructions0,3 mm layer height, 3 perimeters, 15 % gyroid infill.

This is a free teaser pack for the 3dSets Landy Mercenary Kit It includes: -Rear Door wheel mount kit (model 3,4,5) -Short Flat Rear Door (model 3,4,5) -Side Bars (foot rail) (model 3,4) -Door Kit (model 3,4) -Fender Flare Kit (model 3,4,5) -Thicc...

Collection of different license plates for the landy model from 3DSets.Overview&nbsp;Cal01 - 1 Color change.&nbsp;BadNews - 4 Color changes.&nbsp;BLOB Galactic Empire - 1 Color change (BLOB = Big Lump on Board).

I made Kahn Fenders for the 3Dsets.com Landrover Defender Models 3,4 and 5 (it fits also the Pickup Conversion of Model 5). The fenders must be glued to the orig. 3DSets fenders. Also you have to print the included fender flares again, becaue the...