3dsets landy

Alternative side steps, more beefy. ...Doubles as rock sliders. you can get the car at https://www.3dsets.com

Simple Frontlight Glass for 3DSets Bamboo Rc Car. Depending on your printer it should snap in place. ...Might need a superglue.

Fits to buggy from 3Dsets, diameter for tires 53mm. Designed for Tamiya OP-84 53084 - 6029 Square Spike Rear tires. ... Includes two separate bodies for easy 3d printing.

3D printable Fender and Winch for 3D sets Rancher and Landy. ... All parts can be printed, only small amount of fasteners needed. https://cults3d.com/en/3d-model/gadget/modern-fender-and-winch-for-3d-sets-landy Parts can be download under this link.

this is a modified wheel adaptor that will allow the use of the 3DSets Printed wheels with the RC Trailer. i made a mashup of the axle from 3Dsets and the original wheel mount from the trailer. ... this will need supports to print successfully.

Simple Frontlight Glass for 3DSets Bamboo Rc Car. Depending on your printer it should snap in place. ...Might need a superglue.Use concentric top & bottom layers for more realistic look!

VW Hub Cap for 3DSets Model 7 Buggy I have filled in the emblem with black paint for an original look. ... Printed with 15% Infill at 0,05 layer height on picture :-)

Изменено крепление на стандартное как используется 3dsets: 2 болта M3*6 без шляпки и 2 гайки м3. Печатать из термостойкого материала, нейлона или HIPS. ...PETG и тем более PLA не выдержат температуру мотора (проверено)

Male driver is based off of: https://grabcad.com/library/the-male-figure-carl Female is based off of: https://grabcad.com/library/mulher-sentada-seated-woman-human-person-1 Scaled and modified to fit as a driver and passenger in the 3dsets jeep.

I found some makes already available, but the mount hole spacing on the motor I used (FlashHobby D3630 EVO “Turbo”) did not fit the holes in the other makes, so I made a new one from scratch using the 3Dsets' provided 4-hole adapter (printed, and...

... Scaled and modified to fit as a driver and passenger in the 3dsets jeep. ...Figures are recessed into the seats. https://www.3dsets.com/ Print instructionsLicence: Creative Commons - Attribution Category: R/C Vehicles Print Settings Supports: Yes

Model is designed from scratch, based on Tube Doorsteps for Model 1 & 2Required screws for assembly:8x M3x102x M3x8 (rear screws)Intended to look good with accessory Tube Fender Flares for Model 1, 2, 6, but it will fit with the standard fender...

Saw this on a website for resto-modded FJs and thought this would fit the Model 9/10 from www.3dsets.com quite nicely uses M2x6 to mount exactly like the license plate holder. To mount the license plate holder to the jerry can holder you have to use...

Saw this on a website for resto-modded FJs and thought this would fit the Model 9/10 from www.3dsets.com quite nicely uses M2x6 to mount exactly like the license plate holder. To mount the license plate holder to the jerry can holder you have to use...

This is a remix from https://www.thingiverse.com/thing:398515 It uses the same hardware parts as the for the landy. But the some files are adjusted to fit the Rancher. Some holes may still need to be drilled here and there or some filing work. But...

Kahn Front for 3Dsets.com Landrover Defender Models. Match perfect with the Kahn Fenders: https://www.thingiverse.com/thing:4666076 No modification needed. You can exchange it with the Orignal Front, and reuse the holes for mounting the Kahn...

This modified front bumper allows the @lukas_foukal snow plow to fit the 3dsets rancher. The included file replaces the servo guard on the original thing page. Use manifold, left, and right files from the original. No need to make any other...

... 2275122. ...This part screws onto the press and has the shape of 3DSETS calibration print's ball joint pressing area. ... By using this part one can slowly screw the top screw and press the ball joint into the arms without damaging either piece.

I made Kahn Fenders for the 3Dsets.com Landrover Defender Models 3,4 and 5 (it fits also the Pickup Conversion of Model 5). The fenders must be glued to the orig. 3DSets fenders. Also you have to print the included fender flares again, becaue the...

... I didn't want to make it loose, so this is intentional. use M3 grubscrew to tighten I have used a (it seems now defunct) openscad turbine generator for the fan and added a shroud and m3 grubscrew hole you can find the car on https://www.3dsets.com

This is a modification to the 3dsets Land Rover center chassis part to create an integral method of mounting the Injora transfer case as done in the original Bulletproof conversion. This is currently a work in progress so please keep that in mind if...

Wheel hub spacer for Rancher or Landy. Pushes the wheels 11 mm further out and adds a nice 2-piece disc brake rotor because racecar. Print the rotor in silver and the hub in black...or orange...or pink. Whatever floats yer boat. Rotor attaches to...

https://www.3dsets.com/ Print Settings Printer Brand: Prusa Printer: MMU2s Rafts: No Supports: No Resolution: .2mm Infill: 20% Filament: AmazonBasics, Solutech PLA Black, Red, Purple, SemiClear, Post-Printing ============= Other than pushing the...

... I didn't want to make it loose, so this is intentional. use M3 grubscrew to tighten I have used a (it seems now defunct) openscad turbine generator for the fan and added a shroud and m3 grubscrew hole you can find the car on https://www.3dsets.com

Original part from 3DSets is perfectly designed for my 3530 1400 KV Ray G3 motor it has distance between mounting points 27,8mm. My two new motors for tests has dimension listed bellow: 3536 750 KV = 32 mm, 4,2 mm increase 3536 850 KV = 34 mm,...

The Bamboo from https://www.3dsets.com doesn't come with fog lights. I've designed some that are semi-accurate to real lights for the FJ Series. use M2x6 screws to mount them. ###Attention! 1) The glass has a notch at the bottom for the...

The fantastic Model 11 from www.3dsets.com lacked side mirrors. As this is a Meyers Manx inspired car and those had many custom parts I designed the mirrors to my liking, not based on any existing part. 6x M2x6 screws needed to mount them. You have...

The fantastic Model 11 from www.3dsets.com lacked side mirrors. As this is a Meyers Manx inspired car and those had many custom parts I designed the mirrors to my liking, not based on any existing part. 6x M2x6 screws needed to mount them. You have...

The Bamboo from https://www.3dsets.com doesn't come with fog lights. I've designed some that are semi-accurate to real lights for the FJ Series. use M2x6 screws to mount them. ###Attention! 1) The glass has a notch at the bottom for the screw -...

This is a collection of custom-made components for the 4x4 RC Jeep from 3DSets.com that I tailored to work seamlessly with MMU printing technology. This exclusive bundle features only the parts that underwent modifications: Taillights (Left & Right)...