3dbot maker

Special shoutout to maker Benoît Lussier (Printables id: Benoît Lussier) for providing QA printing and quality feedback. A picture of his print is included. See his build under his ID for more details. Another shoutout to Jarvis Henderson...

Maker sure your first layer is calibrated properly and your nozzle and buildplat are really clean. This was the most challanging first layer I printed so far, but if everything is set up properly it just works fine.</p><p>2D Version (black and...

The .scad file is included with this model in case you want to modify any of its design parameters; more information on how to do this can be found in the PPP Puzzle Modeling tutorial.About the DesignerStewart Coffin has been called "the most...

However, I believe that no minimally experienced do-it-yourselfer will be overwhelmed by the task (after all, we are makers!). So, take a look at the materials and tools lists in the PDF manual supplied with the files and decide for yourself if you...

Steps to tap the shaft of the stepper motor: Imobilize the axle with the tool used to secure the thread maker (which means you may need another one); Drill a hole 2.5 mm diameter 10 mm deep into the shaft; Form the thread with a 3 steps M3 forming...

The one I suggest is:By Roma AquaticsAnother great one is:By Maple Leaf Makers - Skip to around 5:00 for the main shroud assembly.Those videos (and more that I haven't listed here) will have you covered when it comes to more general Stealthburner...

Print Settings Printer: Monoprice Maker Architect Rafts: No Supports: No Infill: Probably doesn't matter. I used 10%. Notes: The .stl files used to be 1.065x larger than the OpenSCAD source. This was the scaling I had to use on the last project I...

The original scans are much better quality than seen here, you can easily make out the film grain - a better camera equals better results!\nPrint Settings:\nPrinter: Monoprice Maker Select V2\nRafts: Doesn't Matter\nSupports: Doesn't...

Hi makers!\nUpdate 04/12/17: First print can be seen here!https://youtu.be/JJ2utKqm15Y\nSee instructions section for details on parts and assembly.\nCompleted fine tuning, I'll print off some eggs and post pics from here on out.\nUpdate 04/11/17: Fit...

One maker had good results with 10º, which provides less support and is therefore easier to remove.Filament: PLA (stronger) or PETG (more durable but also a little more flexible)NOTE: If the buttress base does not fit correctly around the height of...

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. ........................................................................................................... **Print Instructions:** Supports: No ...

We've been inspired by Empire State Building + MakerEd Project and some other things on Thingiverse, such as the Finger Wrench. So, we might be using a similar philosophy or shape, but the core of this project, its results, objectives, and mission...

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. ........................................................................................................... **Print Instructions:**Supports: NoResolution:...

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. ........................................................................................................... **Print Instructions:**Supports: Yes (two parts...

I make it a habit to always have an M3 screw set on hand as they are so popular amongst makers and creators. You can purchase an inexpensive M3 screw set on amazon. ...

&nbsp;Just remember to leave enough time for the glue to set before combining too many parts.3 - Based on maker feedback I made some of the connections a bit looser. &nbsp;This turned out to be a double edged sword. &nbsp;The looser connections make...

by Zenmaster_Maker http://www.thingiverse.com/thing:3345859 Banthas (Star Wars Legion scale) by McAnultyMiniatures https://www.thingiverse.com/thing:3958418 Re-sculpted Star Wars Dewback by DaylightInventor https://www.thingiverse.com/thing:2856774...

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Recently got back into...

This last part I left intentionally open, as there is no single and simple solution that fits everyone's needs.Be warned: This is an advanced project for experienced makers! My instructions will provide all that you need to create your own working...

I make it a habit to always have an M3 screw set on hand as they are so popular amongst makers and creators. You can purchase an inexpensive M3 screw set on...

Print Settings Printer: Monoprice Maker select 3D printer Rafts: No Supports: No Resolution: 0.1 layer height Infill: 20% Piece of cake fraction was a test run to see if I could get the fractions to print correctly, and it worked out great! Lesson...

A subtle curvature of the spine and slack in the gate mechanism helps reduces the risk of failure by providing additional shock absorption.Studying other makers of 3D printed components gave a good starting point for to how to adapt these design...

I use Chinese made Sunlu PETG+ on an Ender 3 with Maker's Muse PETG profile. * M6 X 25mm narrow head (8.4mm head diameter with smooth sides) cap screws (8 required) You have to use a similar screw, normal M6 cap screws will not work! I have uploaded...

A Lithophane maker is used to create the file, although this is not a lithophane in the classical sense. Therefore this is a simpler and easier way to create a 3D printable QR code than some other designs I found on Thingiverse (see the links below)....

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. Another shoutout to the guys at 3DBoom (Thingiverse id: 3db00m) for printing a final proof copy of this model. A picture of the front view of their print is...

In conclusion, our rim system is made with versatility at heart to satisfy all types of game makers' different styles in addition with ease when changing everything over at any time we feel. At any time before the last end day we'll try best by way...

Hi makers!This is a wall mounted shoe rack I made to make the hallway shoe-free. Spoiler alert: it worked!It uses a 12mm rod to hold the shoes in place up aganist the wall. there's a lot of ways a shoe fits on this so you can find out what works best...

This is a mold designed for pen makers who want to create segmented pen blanks without spending time cutting individual pieces. The design fills cells with different colored casting resins to achieve the look of a segmented pen. I made my mold with...

I have personally used Spider Maker matte filament for all my prints, and it did not cause any scratches or wear. Q : 是否會磨損/傷害到彈珠 ? A : 不是不可能，取決於你的列印品質和列印材料，越細膩的層高或使用帶有韌性/硬度較低的PLA會是比較理想的情況，我自己使用Spider Maker消光料測試是不會造成傷痕或著磨損。 Q : Will the marbles fit...

... have to experiment. If you want to remix this, please feel free. If you want to post this on another site, again, please feel free. Either way though, please give me credit for this work, and link back to this upload. Thank you! -The Maker Rob