3d weather model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models). If you purchase this transformer with any of our Larson Electronics lights, we will make sure that the connectors are a match.Wiring/Plug: This waterproof power supply is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

1 slot for a pair of Kitchen shears and 1 slot for a Honing/Sharpening Steel.I designed the model into 4 printable parts so this could be printed on smaller printers like the Prusa Mini. But this also makes for easier cleaning since the bottom and...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

The COMPLETE Svartwood Trolls bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Trolls comes in all size and varieties, and being one of the most ancient people, no one knows...

 I have it installed on both my printers and it's really nize.MK3S and (+) versions of the adapter are unique to each model and not interchangeable.Both adapters drop in over the screw heads as shown and get trapped between the extruder body and...

... marked a new beginning in the brand's legendary history while setting a fresh course for the American brand. Visit our website to see more of this model or any other additional services you might need. ... Tires texture not included in this set.

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

The STEP file is included for easy remixing. Please post any makes and if you see a problem please post a comment. Updates: 4-30-2020: Thanks to feedback, I corrected the model for the base, the updated version is "6I". ...None of the other parts...

  ENGLISH-------------Only tested on T12-X, but can work on equivalent models with boxes of the same dimensionsI found my T12-X soldering station a little too bulky, the screen not very visible and too dark. I also wanted to have all the...

Theoretically, it can run more than 11 hours on 1 load (not tested). What parts do you need?Plastic parts:You can use the print files if you have an MK3S or you can use the model files and set everything up yourself. The photos show the position...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

... this design, but don't want the silly text on the knife strip? Check out the modular version! Modular Wall-Mounted Magnetic Knife Strip

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

Scaling up the model to increase the included printing gap, will stop it fusing if this occurs.Step 5Now to starting turning the collar back and forth to try and loosen it up. The box closes by twisting the upper collar anti-clockwise (this can be...

The files are prefixed with Updated_ or New_.Here are a couple videos of it running  Please refer to the Original model for assembly and any other sources.I have uploaded the file as a Fusion 360 archive folder so you will need Fusion 360, Fusion 360...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

Based on the given specification for generating an OpenSCAD script that will output a specific shape model made of acrylic plates, here's the script: ```OpenSCAD $fa=5; $fs=0.5; color("gray"){ translate([4,16,-24]){ mirror([1,0,0]) mirror([0,0,1])...