3d wave model

This model is extremely water-resistant, highly buoyant, and accelerates quickly with my setup. I printed this on my Ender 3 using split parts for easier printing or a single part if your printer can handle the height. The hatch measures 26mm deep,...

However another person created this and the subsequent prusaslicer ini file. however I am not quite knowledgeable enough with gcode and prusaslicer to make the necessary adjustments to it to make it work on the mini (plus I prefer to do it directly...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Finally you should set up channel mixing for tracked models in your transmitter. I added 2 photos of my mixer setup, but this video here explains it very well: https://tinyurl.com/bdns4pj5 It took me half an hour of trial&error negating channels...

It was hard to get some screws in it so I had to manually remove parts that model has removed for you. Make sure if you use screws to hold bearings tight, lowest ones have low-profile heads or they will be lower than extruder nozzles and hit your...

I found red, yellow, and pink lights worked the best with incandescent lights and blue or green appear better on LED lights, in my small sample size. To setup the image to be compatible with this clip: Photoshop/Gimp/other photo editor: Crop photo...

... The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

These models come with an unsupported and presupported version. This Bundle contains the following: Dr. Balthazar Morris Gideon Morris Gravewalkers Gravehounds Medical Carriage(Free in the welcome package for Patrons!) DnD Datasheets DnD...

I have left the original design files as well to preserve version control. Design File Included: .f3d, .ipt, step, .skp, and .obj files. Follow The Makers Workbench...

... with any light color and use a permanent black marker for the text. These models are not designed for dual-color printing. You'll need to print two Monster Ability Card holder v1. ...One is for the Monster cards, the other is for the shop cards.</p>

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

The COMPLETE Thieves Guild bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Thieves Guild AdeptsVery little is known about the legendary Thieves' Guild in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 0 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

First, I modeled the front of the display to fit the RepRap Discount Full Graphics Smart Controller. Then, I also decided it needed a back to protect the circuit board. Easy peasy! Next, I tackled the problem of mounting a TFT35 touch screen...

As with all of my parts, these are modeled after real-world tools, ideas, and measurements using a caliper, feeler gauges, and other tools. Custom Section Objectives The usage of this part will provide the student with a method to replicate...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports. I...

This sword model is a more realistic redesign of the Master Sword from The Legend Of Zelda game series. The text on the front of the blade translated from Hylian says, "The Sword of the Hero of Legend" and on the back, "The Blade of Evil's Bane." ...

Supports are required for this model.In addition to the printed parts, you will need the following hardware:* Qty 2: Blue Male Spade Connectors* Qty 1: #6 x 3/8" Flat-Head Thread-Forming Screw (Wood Screw)* Qty 1: #8 x 3/4" Flat-Head Machine Screw*...

I found when doing this I had to clean my hotend and its was really difficult with this model. ... I included my wires for my NEMA17, but I can tell you right now, your NEMA17 will not be the same, you will have to figure out your pinout by yourself,...

I need thosethree measurements from that photo: Front standoff spacing, back standoff spacing, and front-to-back spacing.I've already helped several people from across the globe and I've been updating this document with the new models as I go.Post...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...