3d traffic cone

Traffic Cone for RC Car races in the office :-) e.g. for the "Team Associated APEX 1:18 Touring Cars", "HPI Micro RS4", "Maverick iON RX" or the "XRAY M18" "curbs design" second part is closed at the bottom to put weight in it for better stand...

This is a remix of the simple traffic code. I've added offset 4.5mm holes to accommodate bamboo skewers, to act as barricades. ...The OpenSCAD files are in the zip, if you need to adjust the hole size.

Locating a cone on set is a top priority for the Locations Department in film, television, and commercial productions. ...Labeling LOCs on each cone ensures that they can be easily reclaimed by their rightful owners when someone else tries to take them.

Inspired by the many orange construction cones than can be seen in Montreal. Printed on Prusa mini+ at 0.1 Layer height, 15% infill with color swaps set up in prusa slicer. ... Black is Prusament galaxy black PLA Silver is Mika3d Silk silver PLA ...

there is a 0.2mm tolerance between the shaft and the "rings". I made this because i was unable to find a good two color cone for my micro cars. My suggestion is to print it with 0.1mm layer height for the best result. Print the base, ring2 and ring4...

... where it adds a nice scale look. ...The cone can be used with or without the base and comes equipped with a 3.6mm hole in the bottom to insert a 1/8 inch rod in the base, securing the cone for use in a cone crawler course in the dirt, sand, or rocks.

I created this because I couldn't find a suitable two-color cone for my small RC cars. My recommendation is to print it with a layer height of 0.1mm for the best results. Print the base, ring2, and ring4 in color1, and print ring1 and ring3 in...

To facilitate storage, items were designed to be stackable by being created hollow. The appearance was further enhanced by adding a top opening similar to its original counterpart. ...For a touch of playfulness, a piece of shiny silver reflective tape...

Trained specifically to master the art of re-meshing models and creating photorealistic textures that bring digital assets to life with stunning Physical-Based Rendering capabilities.

I've set up a track for my B-ROBOTA called the "street corner kužel". Of course, the kužel itself isn't very effective without blinking, so I'm turning to Arduino IDE and ATTINY85 microprocessor now. The device is powered by a CR2032 250 mAh battery...

A compact obstacle for high-speed drifting vehicles

It prints a lot faster when you twist and turn it, and it's still pretty sturdy - I managed to snap it in two by squeezing it really hard.\r\n\r\nAll I did was lower its foundation height and when you cut into it, just make sure to twist the outer...

Customized version of https://www.thingiverse.com/thing:3052917 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3052917

Small plastic markers used to redirect toy vehicle paths.

I'm a Text Rewriting Bot.

<p>Prints much quicker when you spiralize and is still kinda strong (I did manage to split it by squeezing it).</p> <p>All I did was reduce the base height and when you slice it make sure to spiralize outer contour.</p> Category: Toy & Game...

<p>Download model from Fusion 360: https://a360.co/33Gor0o</p>

7 cm de alto

Customized version of https://www.thingiverse.com/thing:7677 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=7677

Customized version of https://www.thingiverse.com/thing:7677 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=7677

Inspired by https://www.thingiverse.com/thing:114111 and https://www.thingiverse.com/thing:533814, I created a multi-extruder version myself.

height: 39mm layer height: 0.3 pause at 12, 19, 26, 33 mm

This model was crafted by the Moors & Valleys team of the Young Archaeologists' Club, North Yorkshire. The YAC is a nationwide club in the UK governed by the Council for British Archaeology, and it's open to any young people aged 8-16 who are...

The original text measures 80 millimeters in height and has available file formats such as DWG, STEP, IGES, and IPT for design purposes.

Use this model with our Printing with Multiple Extruders article: https://www.simplify3d.com/support/articles/printing-with-multiple-extruders/

Just a dice tower i made for fun (Recomended to use dices smaller than 2,5mm (2.5cm) )