3d touch ender 3 pro

I designed this simple 3d touch mount for ender 3. Reason why i designed it like this is becouse i have Red Squirrel Compact Fan Housing mod on my ender 3 pro and this is only way that i can come up with to mount leveling sensore. Also i think it...

(At least on the Ender 3 V2 with the Sprite Pro extruder) You would then set the endstop position to keep the nozzle zero above the build plate. The fit is good, you will need slightly longer M3 screws than the ones originally used to mount the...

I also wanted it to sit in line with the Y-Axis of the printer nozzle.Offsets for the prove are X: 39 and Y: -1 (Z offset should be the same as the stock mount location)I'll link my Noctua 40x40 fan mounts as I finish them as well.UPDATE:...

- Place the assembly on the Ender 3/Pro and start both screws but don't tighten yet. - Press down firmly on the area below the LCD but just above the mounting screws so that the cut away on the back is held against the aluminum extrusion. - Then...

CR Touch offsets are : x_offset: -46.5 y_offset: 0 Hardware for CR-touch probe: 2x M3 nuts With KLIPPER You can modify the offset in the "printer.cfg" file: [bltouch] x_offset: -46,5 y_offset: 0 You may also need to adjust your mesh if you get an...

... Im going to add Cable clips and possibly mount for a LED light and maybe ill lower the camera a little bit more!NO BL/CR TOUCH! Probe sticks out and hits the shroud, Need to cut out a section to clear Thanks OPCategory: 3D Printer Accessories

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

This is a remix of the designs from: https://www.thingiverse.com/thing:4740250 https://www.thingiverse.com/thing:4966561 https://www.thingiverse.com/thing:4749419 I have updated the following: - Updated the components to work with the Biqu H2 V2 with...

This is a remix changing the magnet orientation in order that the magnet is facing the Touch Mi.

This design brings the BL touch very close to the nozzle and accommodates two 40mm fans for good cooling. I run the hot end cooler blowing outward "away" from the printed parts. The design is meant to have 3mm brass melt-in inserts where...

If the two mounting holes are too small for the bolts, adjust the hole offset in your slicer so it prints the files appropriately (you can calibrate to find your needed offset by printing a tolerance test).No supports needed.Setup:You'll need to...

I can ensure you that the CR touch mount is at the correct height, and you wont be digging your nozzle into the build plate. I also added an additional support to prevent the CR touch mount from flexing when probing. It's not pretty... but it...

... nut is a little tricky to get in place, but trust me, it does fit). Possibly could be used with the provided screws with the CR Touch. ... Also, here is what I got for XY Probe offset: -50, -15, 0 (I'm sure it's not perfect, but its working great)

You may need to add a couple M3 washers between the Touch and the mount, as I've found this provides a better Z placement and adds a bit small bit of stability. ------------------- I do plan on redesigning this at least one more time to add a...

I wasn't happy with the touch screen being the widest point of my printer, so I designed this to move it inboard and save some room. It prints in two pieces and snaps together, no supports required. It's a pretty good friction fit so no glue...

Extruder knob for Creality Ender-3 v2 and Ender-3 Pro, Tension Knob, BL-touch mount

Bl-Touch mount for Ender 3v2. In the original bl-touch software (download from the creality website) it is adjusted according to the distance between the Bl-Touch needle and the nozzle tip. When you make Auto home from the menu on your Ender3v2...

... you force the nuts into the top, then you just put the bolts in from the bottom. No more messing around with trying to hold the nuts in place and screw in the bolts. Infill of at least 20% 3 perimeters No Supports Sample offset: X-42.00 Y-10.00

... where you force the nuts into the top, then you just put the bolts in from the bottom. No more messing around with trying to hold the nuts in place and screw in the bolts. Infill of atleast 20% 3 Perimeters No Supports Probe offset: X-42.00 Y-10.00

hi, i was looking for some cr touch bracket, but i've cannot find anything good for my ender 3 pro with satsana fan duct already printed. here you can try this on yours ender 3/3pro. be carefull! at first you have to carefully set the X axis...

Ender-5 Pro BLTouch / 3D touch sensor mount This is a remix from https://www.thingiverse.com/thing:3383611 Just added 2.5mm to bring the sensor a bit closer to the bed.

This handle does not touch the springs and instead grips on the shape of the y axis plate. Each handle also needs a clip to ensure that it does not come off. Line up the bump on the clip with the cut in the handle piece. There are left and...

Ender-5 Pro BLTouch / 3D touch sensor mount This is a remix from https://www.thingiverse.com/thing:3383611 Just added 2.5mm to bring the sensor a bit closer to the bed. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No...

Ender 3d direct drive with Bl-Touch holder. It's really easy to print, but a little bit tricky to remove the supports. Original screws used, you can use the original extruder if you want. Motor cable must be extended. I did by soldering some...

This is a Mounting Plate for the Revo Hemera XS with BL-Touch + 4020 Fan. ...It fits on Creality Ender 3 / 3 Pro / 5 / CR-10. ... Enjoy ;)

(Made to measure for 3.2) Its likey it fits other BL Touch clones, and perhaps the BL touch too. Its fitted by sliding upwards from the bottom, and would offer some protection in the retracted pin position. It also reduces the red light if...

The design has the bl-touch integrated into the mounting plate this idea came from (https://www.printables.com/model/139183-ender-3-v2-voron-stealthburner-conversion). ...but I had to redesign the whole thing as his did not fit the Stealthburner if you...

The design has the bl-touch integrated into the mounting plate this idea came from (https://www.printables.com/model/139183-ender-3-v2-voron-stealthburner-conversion). but I had to redesign the whole thing as his did not fit the Stealthburner if you...

I've installed an all-metal hot end with straight edges, a significant improvement over the stock Ender 3's circular design. To accommodate this upgrade, I've increased the gap between the hot end and the printer frame. Additionally, I've added an...

filament holder for plug-in ender 3 / ender 3 / pro 3D printers