3d touch bfb spool smaller diameter makerbot material

User initiates a 3D touch to trigger a basic interaction and verify that system responds accordingly.

This holder cradles Makerbot 2X printers on MG Chemicals .25kg spools. Spools boast a 1 1/8" center hole and measure 2 1/4" in depth. Printing in two separate pieces, they can be merged together seamlessly. A solid adhesive option for joining the...

I've got my hands on some affordable Jet filament from Amazon, but unfortunately, it doesn't fit any of the spool holders I have or have seen, so I took matters into my own hands and designed this one to work seamlessly with all the spools I've...

CNC 3D touch Probe

3D TOUCH PROTECTION

... ...Built with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=423650. Models Build Instructions Using the following settings: Spool Depth = 80.0 inches angled Support enabled Spool Hole Diameter = 5.2 inches

Designed Specifically from Thingiverse's 423650 Built with Customizer http://www.thingiverse.com/apps/customizer/run?thing_id=423650 Settings: - Spool Hole Diameter: Set to 55 mm - Angled Option: Activated

Select from the settings below to personalize your spool's dimensions: Settings: Thread Capacity (Spool Depth): Set the maximum number of threads that can be stored on the spool, measured in 80 units. Thread Diameter: Specify the size of each...

This is a 3D model of 3D Touch a BL Touch clone. Project contains a .stl and .ipt files and the model was drawn in Autodesk Inventor 2021.

Simple Ender 3 V2 spool holder for 20mm diameter spools.

Z-probe Mount for 3D Touch Sensor on Prusa Printer Auto Bed Leveling. The design challenge was to get the probe as close as possible to the nozzle while keeping the printable area intact. My printer's Marlin settings are: ...

Geeetech brand 3d touch Cover

CLEANER STRAND (3mm/1.75mm) Completely compatible with FILAMENTOS MARKERBOT (SPOOL LARGE / SMALL) Works seamlessly with hole sizes up to 53MM and 52MM Perfect for dual extrusion printing DUAL files are designed specifically for printing with two...

four from bfb!

The files shown here make up parts that comprise a 3D printed Filament Mount, which can be easily attached to the side of your METHOD or METHOD X.\r\n\r\nThe mount is designed to print in no time with minimal support required. Since many mount...

As far as I am aware 3d touch that I have is a clone of the Bl touch so the Bl touch should work. Print on the base that you would mount the touch sensor and use supports, I tried it flipped with no supports and did not like turn out. I have...

Makers use a 0.5lb filament spool that easily attaches to their Dremel 3D20 printer.

Support for 3D touch and short extruder

Made specifically to accommodate Makerbot filament reels, two units will be required for installation. ...It smoothly encompasses a 1/2 inch PVC pipe with ease.

BL-Touch Mount for Biqu B1 1- protect front fan 2- dont need spacer 3- you can use original Bl touch screws or m3 screws

The Ender 3 series "material rack" or spool holder has a 36mm flange. This is the 'newer' design with the steel support and two-piece plastic [round tube 'n' nut] thing that holds your spool. I have an older ender with the one-piece steel holder...

remixed this remix as the orig had errors in the stl shaved off the front and rear to make it look less bulky, raised the bl touch by 2mm for better clearance while printing offsets: define X_PROBE_OFFSET_FROM_EXTRUDER -28 define...

Print without support or raft; remove supports from the Spool Holder Mount, insert the bolt flush, slide on the Spool Holder, adjust for smooth rotation if needed, attach the lock nut with a 1/2" socket, tighten securely but not too tightly, and...

I'w used an horizontal spool holder for a long while, but it tends to tangle the filament thread, this vertical seams much better.

For those interested in the TUSH spool holder, you can find it here: https://www.thingiverse.com/thing:2047554. ... Print settings include: Default print mode: Draft Layer height: 0.3mm Infill density: 25% Shell layers: 3 Infill pattern: Cat fill...

This versatile spool holder fits all types of spools, making it a valuable addition to any workshop. I'm confident it will be useful for many projects. Printed using PLA at 210°C with optimal settings: layer height 0.2mm, raft and supports only for...

I made the lip taller to hold the spool better. Everything else is the same. If you like my designs, consider throwing me a dollar or two to keep the projects coming! ...https://www.paypal.me/disizitstudios

With this remix model, you can install it using the screw on the printer. ...So you dont need anything except bl touch. ...Print 1/10 scale from your slicer.

... Printed with 3 shells and a .35 infill, the holder is solid and prints well. With some acetone application, you can bond multiple holders together for increased spool storage capacity. ...Give it a try and enjoy your new favorite spool holder!

I designed a Low Friction Spool Holder that's perfect for flexible filaments, ensuring they don't stretch out or cause low feed rates in the extruder. ...This design was created specifically for use with my own TPU filaments, as seen on...