3d taylor swift

Each level is divide in eight parts no larger than 27cm, you need to have a bigger printer, or you could split them by yourself using Microsoft 3D Builder, Tinkercad, or similar to those. As it's a very big model, I know many people would want to...

(see the images).Superglue the nose to the body (see the images).Superglue the top deck.Leave the main gun to swing freely.Print supports only on the arches of the nose (that's how I printed it, it might print ok without them).Superglue works best...

At this point Robot5, which is essentially just a nozzle attached to a large robotic crane arm, would begin extruding the molten iron, like a 3d-printer, across the surface of an inflatable dome-mold, to create the roof-caps of our three rooms. each...

If you'd like to back this 3D printed art project, see https://www.kickstarter.com/projects/laird/snowburst-2014 . The project video is <a...

Not only are lots of adapters commercially available, but I've also designed and posted free 3D-printable M adapters for: Argus C3, Minolta/Konica-Minolta AF / SonyA, Canon FL/FD/FDn, Minolta SR/MC/MD, M42, and Kiev 10/15. Notes: There have thus far...

In order to use this setup, you will need to perform extensive modifications to your 3d printer. I've tried to detail as much as I can here, but inevitably you will need to work a few things out for yourself. The setup uses the stock Ender 5...

... cannot be triggered due to the length of its lever, else use A position. The remaining steps should be self explanatory. If you use the fence, don't forget to sand and test it thoroughly before use, as described above. Category: 3D Printer Parts

I give you the 3D printed Sterling main spring forming tool...https://i.imgur.com/j04a7Tb.jpgIt is simply a grooved shaft set to the correct diameter and pitch of a Sterling main spring. The shaft is hollow, allowing you to slip it over a section of...

The idea comes from this fidget spinner: Gobigger Pillbug Spinner Fidget Toy.&nbsp;https://fablades.com/product/gobigger-pillbug/Look for it on the internet and see what I am talking about.The metal version is obviously better but it is pretty...

Make your own custom chips.Accessories&nbsp;DescriptionImageFCS Label Mounting SolutionUse this to label what filament is stored in your dry box, Ikea samla or where ever else you want to label filament.FCS Label StandUse this to see what material...

A 3D printable Artisan Case for a single 1U Keycap or 6.25U Spacebar. It uses an optional Tenting Base and can be used with an Acrylic Cover for added protection. It also features a conservative keycap stem holder to keep your Artisan Keycap in place...

###Latest version (v4.0): https://www.myminifactory.com/object/3d-print-169440 ------------------------------------------------------------------------------------------------------------- * ***This is my second attempt on creating a mechanical...

For instance, Alpaplastic (with 4 models listed below) is not a filament manufacturer, but a spool manufacturer whose spools are used by many filament brands, especially European: Fillamentum, ColorFabb, Spectrum, Extrudr, Smart Materials, Sakata 3D,...

Das Locht dient nur dazu das ein &nbsp;Sechskantschlüssel durch paßt um die Linsenkopfschraube anzuziehen.Die 535mm und 396mm Profile werden Stirnseitig mit einem M8 Gweinde versehen und im Voron Style verschraubt.&nbsp;&nbsp;Print SettingsPrinter...

There is a bit of tolerance built into this to make it a tight fit with respect to the slight shrinkage that happens in 3D printing. Be prepared to use clamps to squeeze the nut into place. Mine was able to just push in with my thumb. - qty. 2 of...

3D printers with a special alloy, fully recyclable, will print all the mechanical parts and tools needed during the missions. This will save a lot of weight for the trip to mars and will grant flexibility by building the best tool for the right job...

There is a wide range of radius sizes from 5mm up to 200mm and 0.5" to 8", all carefully optimized for best usage.About the DesignI designed all templates from the ground up, specifically to be printed on a 3d-printer. The design is optimized to make...

...Nails and 3D printed parts are cheap and easy to replace. 7.6mm fits best. Any nail with Ø6-7.8mm (8mm model) and a length of at least 15-20cm should work. I'll add a 6mm model for smaller nails but they may be to short or don't stick in the ground.

So, 3D print to the rescue. I found a printable full-size Captain America shield on here (Link to thing), but it said "work in progress", so I designed my own. I was especially unhappy with the way the parts were split (21 pieces), and that there...

Now that I do own a 3D printer, I went and created a nice and customizable planting pot to finally make use of that otherwise rather useless down-spout. \o/Since everyone's situation will be different and there does not seem to be a standard when it...

... a plate to mount a hemera. I have uploaded a base and front plate specifically for the hemera. Print Settings Printer: Sidewinder X-1 Rafts: No Supports: Yes Resolution: 0.24 Infill: 35% Filament: Sunlu PLA+ PLA+ Blue Category: 3D Printer Parts

The code is a bit messy (especially for the rack), but it should work for most reasonable settings. This way you can also increase the resolution of the 3D models, Due to size constraints they had to be rendered a bit low. Using this bash script you...

If not, here is a good pair you can buy (local hardware store is the best option):...

See pictures for examples. Print instructionsUnassociated tags: Filament Buffer, spool cuff Category: 3D Printer Parts How this works A basic demonstration of how this should work. Design Goals Spool cuff should: Work as a reliable filament buffer...

Cómo configurar los parámetros para personalizar la impresión del pomo en “U” 2.1 Para poder personalizar el pomo en “U” deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de un software libre y se encuentra...

ESP32 DevKitC (v1 or v4 tested)...

Here you go The Modular System - Flexible Mask Rolley https://www.thingiverse.com/thing:4280201 Need a Goggles, please check https://www.thingiverse.com/thing:4317517 If you have 3M Half Facepiece, please check...

Violence is never more than a heartbeat away.Use those guns! Deliver your cargo!Stay in the fight!Small painted-on supports are required for Gun overhang and Freight Ten gun mounts (Support Enforcers Only.)Glue gun mount onto the Cab (see...

Description: A set of 3d printable parts to compactly combine two LRS-350 PSUs into a compact unit with optional voltage and current displays. I put this device together so i could consolidate the 10+ individual power bricks for each compute node in...

Egg LatheFor painting eggs.&nbsp;Not for turning them!See also 'Egg Lathe UPDATE' for alternative parts that replace the gears for a smoother rotation at https://www.prusaprinters.org/prints/153374-egg-lathe-updateNOTE:Now includes STL files to allow...