3d splash model

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

 The fan mounting holes are sized to accommodate a Brass Heat-set insert size M3x4mm.  The holes are not threaded and too large to accommodate an M3 screw itself.   Upgrading the Raise3d Pro2 with a Copperhead  Note: Both Hotends must be replaced...

And get your supports in order first, the models need a relatively precise and flat supported surfaces. <font size="3">The modification uses many parts from the original setup, but the PTFE tube must be cut, making this a non-reversable mod...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Modified the vent slots on the right side so they are less likely to cause problems during print. I really liked the compact ATX benchtop PS by gdoniu93 and started out simply to recreate the model in Fusion360. Somewhere along the way (as it often...

I have completed assembly and everything works so this addresses some of my main wants for this awesome model. I am also going to include the full parts kit here (the originals I used also), so everything you need is in this one thing saving any...

[Large Sized Model - 25mm base] [Presupported in 32mm and 75mm scale]   One of the most respected Warbosses in the armies of Berogtor’s Yellow Orcs. Gazza was once a wonderer, living in the harsh arid land of the fallen Anshani Empire. He accrued a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

They were sold to me as "boat nails", feel free to substitute them for something else and adjust the model accordingly. For the spark gap I used a couple of bits of single stranded wire, these can be substituted for something else, multi-strand...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

To do this I went to https://3dp.rocks/lithophane/ sized it in model settings, and set it to Positive under image settings. I kept it flat since it will be used as the back of the bookstand. But while it's not in use it can also be used as a cool...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

Which means planning so the bridges will look nice enough/not stand out too much.This also means some very precise modeling so that the slicer can handle a bridged over area with a hole in the middle. Here, I build up to it layer by layer with...

https://www.printables.com/de/model/172064-phaetus-taichi-mount-and-fanduct-w-dual-5015-fans- ________________________________________________________________________ This is an highly integrated Mount and FanDuct for the upcoming Phaetus TaiChi...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_size = 40 stencil_shape = 4 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Already renowned for their authentic sound, Casio's latest model takes it to the next level with its impossibly small footprint. Measuring 43 percent smaller than previous generation Privia instruments, the PX S1000 is literally half the size of...

This is a model of a convenient sliding lid box with an easy to use locking mechanism consisting of a bump on the lid that keeps it securely closed. Note that for slim boxes the lid does not bend as much and the locking and unlocking may be a bit...

A great way to combat this on any print with sharp corners is to add “Mouse Ears”.• Add these in PrusaSlicer by right clicking on the model in the list on the right of the screen, hover over “Add Part” and select “Add Cylinder”• With the cylinder...

It was hard to get some screws in it so I had to manually remove parts that model has removed for you. Make sure if you use screws to hold bearings tight, lowest ones have low-profile heads or they will be lower than extruder nozzles and hit your...