3d skrivare

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

It includes BL-Touch/3D-Touch support, filament runout detection and power loss resume - only functions from SDcard. The firmware.hex file is included. DISCLAIMER: If you are using the firmware.hex file you are doing it on your own risk, since...

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

Dragon and Mosquito use the same length of PTFE tube which is why they share jig.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress. Shipping takes a while from China but quality is excellent and the prices are...

My bot came with 410 mm Y rods, which is reflected in the Blender file, but this design should work on older printers with shorter rods (the original i3 had 330-335 mm Y rods). The .blend file depends on my standard parts/materials library, which can...

See “Large Binder Clip Tentacle Monster” below in connectors.Tentacle Rail Clip BaseThis Tentacle System base includes a clip that attaches to the T-Slots in the aluminum extrusions used in Prusa and other 3D printers. Used in combination with the...

I did not try to 3d print everything in plastic if metal or wood made more sense and was faster/stronger/easier and not cost prohibitive.  3D Printing is mostly used for the connections and exact positioning of tubing.Everything here is my own design...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

Possibly by using simulations.Rails as a wholeSince my 3d printer is not big enough to fit 120cm ring on it (its bed is 210x250mm) I needed to split rails for printing and connect them afterwards. I decided on using M5 bolts and nuts.</p><figure...

I've spent quite a bit of time getting to this design and I want to make it as accessible as possible so that as many people as possible can enjoy the greatness that is easy loading/unloading of the MMU. Good luck and enjoy!! Print Settings Printer...

(That's something else, sorry.)Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

How to make your own module for the phone holderIf you know how to use 3d designing software here are the dimensions to make your very own module for the Modular Phone Holder! All the modules use a very basic system: to start, the main rotating part...

Here's a comparison picture by Hercules user techguychad: What to print: Print these files: hercules-1.7.2.stl hercules-dial-holder-1.3.stl hercules-belt-peg-1.2.stl hercules-fan-duct-1.3.stl bmg-handle-short-1.0.stl...

Potřebné vybaveníNotebook nebo tablet, programy Tinkercad a PrusaSlicer, 3D tiskárna.Nepovinné - krabička čtvercových rozměrů, tvrdý papír, pravítko, tužka a nůžky (viz postup).9. Potřebné soubory a dokumenty (seznam...

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

Note that if there is more than one row or column, the row or column spacing still will be applied (which can be useful to match a specific size).An optional area for adhesive label (which IMHO work better than adding a 3D printed text). It's...

I think the pipeline will look even better in PLA.Designed on Tinkercad.No supports required.Superglue the valve handles.Also, see:Above Ground Pipeline Addons - https://www.printables.com/model/222945-pipeline-addons&nbsp;Space Port Fuel Station-...

If you want to add time indicators to the watchface I'd recommend using roman or greek statues holding the numbers, to fit the theme.&nbsp;UPDATE: I've added a few statues with numbers to make reading the clock a little easier, they are based on the...

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

With external markings and without.Stand up your Space Port before it's too late!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under...

Now you can print them out and use them for your nefarious purposes as you travel the far and vast star systems.The Original Galindos - https://www.printables.com/model/143724-galindos-robot-model-science-fiction&nbsp;Galindos Evolved -...

(That's something else, sorry.)Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

I present to you, what is likely one of the only mechanically working 3d-printed Prop Revolvers available, especially for free!Go here to see it in Operation: https://i.imgur.com/DBUVUkF.gifvIt is quite well balanced, see here:...

If do you need to get the lock back off, the best way I found was to stick long allen keys into both of the lock's holes and then pinch them together to lever the lock slightly apart, which reduces the pressure enough that you can wedge a thin...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

By doing so, I can now get more of the STLs to show up in 3D view on this site. The updated files have 10-18-23 dates and are renamed with "-remake" or "-k". 10-10-23 Update: Two items - Assembly Hints and Images added as a new section, and an...

What to print: Print these files: icarus-1.2.1-for-sherpa-mini-r1-normal.stl sherpa-mini-r1-dragon-mount-1.1.stl icarus-dial-holder-1.0.stl icarus-belt-peg-1.2.stl icarus-fan-duct-1.3.1.stl...

Avoid lifting and warped prints!Print all three parts (body, cab, treads)Superglue the treads to the body.Superglue the cab to the body.Superglue works best for gluing it together.It will scale easily if you want a larger or smaller...

These strips are bright enough I didn't notice only one was on. View from Octoprint Control tab during the first layer of my first print after installing. Print instructionsCategory: 3D Printer Accessories Summary Prusa i3 MK3 PiCam v2 X-Axis Motor...