3d shirt design

I've made the complete design open source so people can build their own with the exception of the software. I'm asking for a contribution of $25 for a copy of the software which runs on the Arduino Uno. You may also write your own software. I'll also...

To reduce the risk of joining the two parts I have constructed a design aid. This should allow the hinge to open without too much force. More details in my video :) Also, a small area is cut out to leave room for your finger when prying it...

A supply droppod inspired by the Tacticus game.The lid can be opened.Can be retrofitted to act as a lifeboat for up to 12 persons.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my other...

These are some floating, topwater popper lures that I designed and printed, based on some store-bought ones. They were a lot of work to get into proper working order, but look great and catch fish, at least in my neck of the woods. What you will...

** You can purchase this case printed from my store by clicking HERE **This is a case for a RAKwireless RAK 5005-O WisBlock base board, designed with the Meshtastic project (https://meshtastic.org) in mind. ...It will accommodate the RAK5005-O base...

I used TinkerCad for the design. It has limitations of number of facets in circles which shows up more with large diameters but still looks pretty clean when assembled.Post Printing: After printing, test thread fit. Be careful the threads can be...

This allows you to add new functionality to Omnipanels without needing to design and print complete new panels. The R1 and R2 variants have gaps to fit with reinforcing clips.</p><figure class="image"><img...

The nut holes are designed to hold M2.5 nuts by friction but gluing them in just in case is a good idea. I need 5 M2.5 x 8mm screws and 7 M2.5 nuts (minus the camera part). The 18650 socket comes from https://www.thingiverse.com/thing:456900 by enif....

I had problems with the first design of the belt adapter. It was not strong enough and broke easily. So, I replaced it with V2, which is stronger and has a better orientation for printing in the "flat" plane for strength. If you only have one...

Introduction:&nbsp;The design was made to be aesthetically pleasing, offer improved part-cooling while also supporting a BL-Touch or CR-Touch ABL. It is a replacement for the stock cooler however will require an additional 4010...

This is a recreation of the soda can tank I made a remix of, unfortunatly the original files from the original creator are no longer available.Therefore I made this.Contains all pieces from my Remix too.If you like my work please consider supporting...

LCM Nearfield monitor speakerThis is a near field mini-monitor, designed for excellent bass response, and intended for use at a desk or console. They are suitable for desktop, shelf, or wall mounting and optimized for small to medium sized rooms. The...

Dont order parts upfront if your unsure the files can be printed with your printer.And with that out of the way lets get back to the project._________________________________FEATURES: Rugged case with TPU bumpers12" Full HD IPS Panel ( low power...

It was the perfect location for a factory designed to build nightmares, since no-one could hear the screams or explosions. It was here that The Overseer crafted his Iron Acolytes, an unwilling fusion of man and machine. Once dissenters against The...

It is designed to be printed on a 300mm(~12inch) bed.You will need to print:(5) Sides(1) Plug Side(6) Ring(6) Cut Guides &nbsp;&nbsp;You will need to purchase:(2) pieces of 0.093"/2.4mm acrylic at least 30"x30" (or a large one you can cutto make...

This carriage and extruder setup weighs 40% less and slides much more smoothly with increased movement accuracy on the linear rail than the stock Qidi extruder/carriage.The associated linear rail gantry files can be found here:...

You will need to print: -Top Replacement pieces for FFC Pro: FFC PRO Vent Top Left and Right (2 pieces total) -Duct to mount to top of new FFC Pro Top: 4in Vent adapter from ffcp01 file duct.mount (1) -A 120mm Fan to 4in Vent Hose adapter (1)...

The proposed modification to replace the ABL sensor with an inductive sensor makes sense if the printer is equipped with a metal PEI board.Additional comments.The PRUSA SUPERPINDA sensor has a standard deviation of less than 0.005.The measurement of...

So I used the "center" (it is actually a little off center, by design, instead being closer to the edge of the 2020 frame) bolt hole to secure the mount, then the outside 2 holes to mount the bushing to the frame. For the edge that "hangs out" a...

These designs are tailored for the game and each one is just 2 inches long (the same size as the board game pieces). You can resize and print them at any size you prefer, but keep in mind that many details are exaggerated to ensure they show up...

If you are using Arduino IDE, look for file src/main.cppInstructablesYou can also find this project as instructable at: instructables.com/AutoShopVacSwitchLicenseThe design files are published as-is, CC-0 / no rights reserved. ...Attribution when used...

This goes for any author's design. ----------------- Extra Notes: Tolerances between all parts/interfaces have been reduced to 0.1mm-0.25mm. This leads to much higher frictional forces to be achieved while still allowing for some free...

this is designed to fit underneath hopefully any Hornby 0-4-0 shell. as part of this, I've included a back piece, and two front's with and without cylinders. there are also two versions of each piece, one for Percy wheels (15mm Dia) and for Duck...

Thanks to the awesome Delta P duct design by @teookie, I saw a significant increase in air cooling flow, so I did a remix and added 2x LEDs to let me see the extruder.That remix is here:...

It's designed to fit snugly into the bin to absorb dice throw impacts.Color: Clear07 - Big Carrot BoxPrint 2 of these. They will fit into each other to hold the Big Carrot cards.<br/>Color: Orange</li></ul><p>08, 09 - Small Box</p><ul><li>Print 6...

The different models are designed to fit together to facilitate their installations, to be used for cables with small sections. Fixing holes: d = 2.2 / 4mm - Be careful, use a nail or a flat screw, do not overdo it at the risk of breaking the...

Make sure to test the right direction before forcing the magnet into its hole .... How I Designed This Changes to the code. I took the code from Daizyu and came up with 2-3 interesting configurations that required some change in the code. E.g. ...the...

________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Tinkercad link: ________________________ Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet...

...Instead, I designed the hull in two halves, which are attached to the aluminum case of the power supply to the places of its attachment. I drilled a 3mm hole in the corner of the front of the power supply to bring out the variable control resistor.

This is the Vaessen Motorsports sequential shifter, I have designed this to be a solid shifter with a mechanical feel. It also involves off the shelf parts to make assembly easy. You will need a basic set of tools and a soldering iron. I would...