3d scanner turntable

... mounting onto a 28BYJ-48 stepper motor. For more information, check out our latest blog post on the 3D scanner project! Blog Post: http://www.theprotolab.com/2020/04/24/affordable-3d-scanner/ OpenScan V3: https://www.thingiverse.com/thing:2755968

The turntable operates in three modes: - Mode 0: No actions - Mode 1: Push button starts rotation, adjust angle with potentiometer (no scanning) - Mode 2: After pushing button again, table stops for 5 seconds, moves away, rotates, sends signal to...

This replacement turntable is designed for the Matter and Form V1 3D Scanner. I bought two used scanners that had issues with guide bearings - the pins they snap onto were broken, causing a significant amount of lateral slop during scanning. It's a...

This is a replacement turntable for the Matter and Form V1 3D Scanner. I purchased two of these scanners used and both had issues with the guide bearings. The pins they snap onto had been broken which resulted in the turntable having a silly amount...

This is a replacement turntable for the Matter and Form V1 3D Scanner. I purchased two of these scanners used and both had issues with the guide bearings. The pins they snap onto had been broken which resulted in the turntable having a silly amount...

As I printed the original design for my scanner (v6 was its state when I built it), I noticed that often the turntable wasn't secured and thus was hard to rotate without moving out of position. ...However, by using these simple grips to latch onto...

As I printed the original design for the scanner, I quickly realized that the turntable often wasn't properly secured, making it difficult to rotate smoothly without shifting out of position. ...However, by incorporating these straightforward grips that...

Parts required: 1) 3D-printed components from Shapeways - https://www.shapeways.com/shops/virutmake?section=Turntable&s=0, 2) a 360 Degree Servo (e.g., Modelcraft Spezial Servo Digital - RS-10, double ball bearing gearbox, plastic, with JR connector...

This is a turntable designed specifically for 3D scanning purposes, as showcased in the accompanying video: https://youtu.be/moVuucoa0N4. The key feature of my turntable is its ability to adjust camera distance and angle on the fly, eliminating the...

An open-source, Arduino-based 3D scanner turntable for small objects is demonstrated in this project. Check out the video at http://youtu.be/n9UiJGrGvfY. To build it yourself, you'll need an Arduino Uno, a stepper motor, an EasyDriver stepper motor...

After numerous events where guests reported dizziness from standing on the original turntable, I decided to modify it so that the 3D scanner revolves around the object or person instead. The updated design includes an adjustable extension arm for the...

A turntable for a 3D scanner, etc. Designed to be printed with no supports, no brim, no raft, and minimal cleanup. Easy assembly, versatile - can be set up as 6-to-1 or 24-to-1. Can easily add stepper/servo motors, cams, etc. I intend to use...

After researching online, I've decided to modify the turntable so it rotates around the 3D scanner instead of the objects/people. To enhance my design, I've added an adjustable extension arm for the camera dolly and a vertical track for the 3D...

The engineer installed a reliable d-shaft locking bolt and nut assembly to keep the plate firmly in place during rotation.

As it can be programmed for variable speed, this actuator can also function as a turntable for 3D scanning purposes. To convert it into a 3D scan turntable, simply mount a cake-plate on top of it. No printing is required; merely apply glue or...

As its speed can be programmatically controlled, this mechanism can also serve as a 3D scanning turntable. Simply attach a cake-plate on top of it; no printing necessary, just glue or screw it in place. Add some silicone lubricant to the moving parts...

Turntable, supported on 6mm balls (valid airsoft balls) driven by a stepper motor and controlled by Arduino whose purpose is the improvement of photometry app (QLONE) for 3d scanning, also valid for product display with a touch of dynamism.

The 3D scanner, FabScan, features a turntable measuring 12 cm in diameter, complete with an integrated interface for its stepper motor.

These are printable parts for a 3D scanner turntable base that sits atop a standard Nema 17 motor. The turntable plate and modified ciclops gear fit on top of the base. Assembly Instructions Step 1: Secure the knob to the motor shaft with a small...

This turntable is designed for a 3D scanner and can be printed or milled; however, milling may result in waste. It can be produced using a MakerBot with parts within 10x10 dimensions and requires a Solarbotics GM3 motor. Created months ago and posted...

3D scanner turntable This minimalist turntable can be used for 3D photo scans. The object to be scanned is placed on the plate and can be photographed from all sides by simply turning the crank. Using the appropriate software, the images can be...

3D scanner turntable This minimalist turntable can be used for 3D photo scans. The object to be scanned is placed on the plate and can be photographed from all sides by simply turning the crank. Using the appropriate software, the images can be...

We have a simple cellphone scanner turntable that's easy to print and use. If you want to turn it by yourself, use the "kurbel" (that's German for "hand crank"). In my case, a motor is doing the job with the motorhalter and adapter. You can find the...

After stumbling upon the source code for a 3D scanner turntable online, I made the decision to design my own setup. All credit goes to Whitney Potter for creating the original code. The source code can be found here:...

After finding the source code to a 3D scanner turntable on the internet I decided to make my own design of a 3D scanner setup. All credits for the source code goes to Whitney Potter for making the code. Source Code can be found here...

scanner 3d con telefono

Inspired by a similar initiative (http://www.instructables.com/id/Lets-cook-3D-scanner-based-on-Arduino-and-Proces/?ALLSTEPS), I designed custom components, including the turntable, laser, and camera holder, for my 3D printer. The ODT (Libre Office...

3d scanner based on intel realsense d435 camera

proto scanner 3d I am looking for a programmer to make it work

This project involves creating a 3D scanner with applications in graphic design and medical fields. ...As a collaborative effort, it features contributions from myself, Brice Veyna, as well as teammates Mohammad and Abdullah Alqahtani.