3d printing temp tower

Since I could not find the ideal temp tower that meets my expectations, I designed my own.Features:- Uses little material because it is not too big- Different overhangs, 45° and a curved one- A thin wall at the overhang to test the layer adhesion by...

This is a higher-temp test tower intended for PLA filaments that like it hot. Starts at 235, cooling as it climbs to 195. This GCode was generated with CURA's post-processing scripts, and has only been tested on my own Ender-3. 3 versions for a...

My expertly crafted PETG Temperature Calibration Tower is specifically designed to function optimally when printed at layer heights ranging from 0.05-0.30mm. This file has been meticulously optimized for use with 3.2mm nozzles and features three...

... ...Functions perfectly when printed anywhere from 0.05-0.30mm layer thickness. File specifically designed for 0.4mm nozzles with three exterior walls.\r\n\r\nCustom version of http://www.thingiverse.com/thing:915435\r\n\r\nCreated using Customizer!

It's more detailed in the Recymbol entry, but in a nutshell you just print the symbol, remove purge line and skirt, change filament, and print the tower just on it ("print-on-print"). ...There's an offset to the negative spaces in the tower so there's...

A compact calibration tower to calibrate temperature and stringinig for PLA, PLA+, PETG, TPU & ABS

My expertly tailored PLA Temperature Calibration Tower is designed to deliver optimal results when printed at a layer height ranging from 0.05-0.30mm. For best performance, it's ideal to use this file with nozzles that are 0.4mm in diameter and...

14/03/2021: V2 - Larger overhang & adding each temperature block to create your own temperature tower A compact tower to calibrate temperature & stringing for PLA, PLA+, PETG, TPU, ABS

Use the temperature tower at your own risk! ... Simplify3D Flashforge Adventurer 3 Basic PLA Medium Profil Primary Layer Height: 0,2 mm Infill : 20% Rectliniear

This is a Jaws of the Lion initiative Tower for the 2nd printing, which has larger initiative cards. I didn't see any others on Thingiverse so I made my own based on this 1st printing tower. Realistically the tower doesn't need to be as thick, but...

Gcode for Stock Ender 3 Temperature Sweep \r\n\r\n\r\nLayer: \r\n0.1mm\r\nFirst Layer 0.3mm\r\n\r\nInfill: 20% Density\r\n\r\nSpeed:\r\nFirst Layer 20mm/s\r\nWalls 25mm/s\r\nTop and Bottom 50mm/s\r\n\r\nBed Temperature:\r\n60°C\r\n40°C (Temp 40...

... various aspects of the printing process, including robust slicing, retraction behavior, and thin wall types. Overall, this configuration file is used to customize the behavior of Cura and fine-tune its output for specific 3D printing scenarios.

... at ten degrees make fifty layers. Example: Layer one is printed at 260 degrees Celsius. Layer fifty is printed at 250 degrees Celsius. Layer one hundred is printed at 240 degrees Celsius. ...Layer one fifty is printed at 230 degrees Celsius.

Temperature Tour for Anet A8. ... Printing at 0.2 to 50 mm/s speed from 170 to 210 degrees Celsius.

We print in 0.2 inches per 10 degrees, which is a total of 50 layers. The contour is 0.8mm. Example: Layers one equals 240 degrees Celsius. Layers fifty equals 230 degrees Celsius. Layers one hundred equal 220 degrees Celsius. Layers one hundred...

I searched for a ready one on thingverse but it wasn't there and my girlfriend needed it for her 3d printer so I made one. Use the Gcode provided and ignore the stl. I hope this wil be helpful to a lot of people. This has been realised for cr-10...

I searched for a ready one on thingverse but it wasn't there and my girlfriend needed it for her new 3d printer so I made one. Use the Gcode provided and ignore the stl. I hope this wil be helpful to a lot of people. This has been realised for stock...

Right Tower: The tower dimensions are ten millimeters by fifteen millimeters, to the edge of the arc portion. A fillet measures three millimeters on the bridge side of the tower. Slits measuring .5mm and 1mm wide are located on the back of the...

Just another Print Tower to test filament temps There are lots out there, but i needed one a little thicker to give me better string testing

Just another Print Tower to test filament temps There are lots out there, but i needed one a little thicker to give me better string testing

Customized version of http://www.thingiverse.com/thing:915435 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915435 Instructions Using the following settings: Number of Blocks = 4 Must Modify...

Customized version of http://www.thingiverse.com/thing:915435 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915435 Instructions Using the following options: NumberOfBlocks = 5 Labels =...

Customized version of https://www.thingiverse.com/thing:3438677 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3438677