3d printing database

Print SettingsPrinter: Velleman K8200Rafts: NoSupports: NoResolution: 0.25Infill: 30%Notes: You'll have to put in 1mm support columns on the base lip where the cups are pulled out. If you let Slic3r handle it there will be a lot of wasted plastic. ...I...

For this team project i worked with Joanna Su (link) Problem Statement: With a partner, you will design a “2D” placard using Solidworks.  You and your partner will have the same design which meets the constraints below, and you will EACH use...

The gray and orange caddy shown here was my prototype and a number of improvements have been made to the design since it was printed, mainly regarding the fit of the deck boxes, keys, etc. The largest dimension on this is 9.7", with the height...

August 17, 2018 I added videos with Banebot wheels and improved stepper support: https://youtu.be/ayka_9WWK08 https://youtu.be/4J9OeD_G4EI https://youtu.be/0Lg4ioItwHg March 10, 2018 First garage tests: https://youtu.be/bwohv99UVjI...

... LiPo buzzer is too loud stick two pieces of bubble gum into holes of little speakers, that will make the sound muffled and still loud enough for you to hear it. Enloy printing and building. Have fun, don't forget to like. ... Category: R/C Vehicles

Assembly Once all parts have been printed, support material removed, and cleaned of debris: 1. Turn the hopper upside down. 2. Insert desired cup type (e.g. tap) into the cup hole, so the flange is flush with the gap at the end of the cup hole. 3....

... any surface with screws or nails. I may explore a way to use these to make a suspended version of the dispenser. Nota3: don't mind the colors. I ran out of black PETG during the print and had to switch to white. ...In the end it's not that bad.

RPi3 Model A can be mounted too, but a lot of creativity would be required. Assembly requires some screws. Driver board – 4x M2, M3, or #4 wood screw (example) Mounting brackets – Some M4 or #6 machine screws (example) （更新 2019/3/8) 新しいバージョンを公開しました...

If you use Marlin, you could set in Configuration.h: ``` #define X_MIN_POS -15 #define Y_MIN_POS -15 ``` Print with ABS or with any rigid plastic which works in your temperature range. Take into account that the mount contacts the stepper motor which...

Here are the necessary components: Raspberry Pi Zero W (1) Screws (2.2 x 4.5mm) (7) Nano Servo (e.g., Turnigy T541BBD) (1) Videos demonstrating the project in action can be found here: https://www.youtube.com/watch?v=_hPZF4_aZSA...

different clamping nut sizes.And this is the result of some drawing and printing.• Part 1 is the mounting plate suitable for all diameters of clamping nuts.       This is mounted on the tool-holder plate using the hole in the plate to secure and an...

Parts List: Switch, Latching 17x12x9mmhttp://www.ebay.com/itm/6-Pcs-Horizontal-2-Position-Latching-Action-Torch-Push-Button-Switch-/321687308113?hash=item4ae60ec751 Adafruit Mini Lipo w/Mini USB adafruit.it/1905https://www.adafruit.com/product/1905...

Depending on your print tolerances, you may find that you're unable to twist it that far. In that case, take the SCAR off the barrel, lock the sleeve so the barrel-gripping fingers extend into the inside, and file away some of the high points of the...

... the sulfur and phosphorous expansion set (http://thingaverse.com/thing:2350618). Print Settings Printer: Da Vinci 1A Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 mm Infill: 10% Notes: Three perimeters works well. ...I used ABS.

... I have not mounted the printer, controller, and power supply on a base board, so the wires to the controller are not cut to length. It's still pretty messy, but I'll do it once I'm happy with the design and fix everything down. Happy printing.

2.6mm thickness - I used something like these:...

It's essential to print this component in HIPS or a similar material that's more heat-resistant than PLA. I've tested it with PLA, and while it works initially, it deforms and becomes brittle over time. Additionally, the cooling duct was designed for...

Here are the dimensions for the eye module: * Length: 100mm * Width: 45mm * Height: 30mm All the parts were printed using ABS and then treated with an acetone vapor bath to give them a smooth finish. After the vapor bath, I drilled holes in all the...

if using the file named base_with_better_band_support.stl then this has built in supports that need removing, it is where the rubber band slots in.I designed this to use the MadLab MLP105 Electronic Kit, Junior Theremin as it works the same way as a...

... or nails. I may explore a way to use these to make a suspended version of the dispenser.Print SettingsPrinter Brand:Prusa Printer: I3 MK3SRafts: No Supports: NoResolution: 200 Infill: 15Filament:Prusament PETG     Category: Outdoor & Garden

... points. This needs supports for building (you might try flipping it upside-down to check if you need less material - this depends on your printer). Also added full- and half-height main body extensions (these can be printed without support).

To get GPIO pins working properly for this print, please follow these steps: Before you begin, please follow the steps in this walkthrough: https://www.klipper3d.org/RPi_microcontroller.html?h=gpio You do not have to follow the link under Remaining...

Edit 1: Separated the crab from Kraken Guard shoulder 3 to make it a bit easier to print. You'll simply need to attach Clad in the strongest armor the Legion has to offer, Tide Lords act as the shock troops and personal guard of high ranking...

Deprecated: Please use newer V2. This is my attempt to design a mount for the Bondtech LGX extruder with the LGX FF for flexibles hotend kit. The extruder is mounted sideways attached to a mounting plate via two M3 side screws into the extruder...

*Printed and checked. Passes XYZ Calibration and Selftest.* **Credits:** --------------- 1) Inspired by the MGN12 Linear Rails designed by Stwebster (https://www.thingiverse.com/thing:3400952) 2) Y-Tensioner and Z-Motor_Mounts are modified...

Update 2022-01-17: I've started adding .stl files for Ender 3 based on measurements provided by [Nolemgib](https://www.thingiverse.com/nolemgib) (top: 25cm with screw holes, bottom 13cm with cutout at one end, vertical half 20cm (40cm can not be...

The rods should be cut to length (about 86mm, give or take, size them up against the holder once it is printed). I'd recommend cutting them so that they have about 1mm to 2mm play side to side once installed; if cut too snugly they can extend past...

Instructions Bill of Materials 3 or 4 - 1m OpenBeams depending on the size you want (6) 13/32" x 1" compression springs (44) 3m x 5mm screws (44) 3m nuts 1.75mm filament 4 corner open-beam corner pieces (optional for improved stability) 2 OpenBeam...

For this particular item, print two backs, two bottoms, one front, and three sides (H2). Slide the bottoms through the sides and push them back to lock in place. **Update 5/10/2020**: American Mini cards are now included, with a single row, two-deep...

... as an individual piece: top, bottom, button. Make sure to leave the translate and rotate function commented when compiling for export so that each piece is flat side down. I printed mine at 0.15mm layer height and 25% infill and it worked nicely.